Acura CSX. Manual — part 447
06
SNR9A00J26220219251KDAT00
SNR9A00J26220200000KDAT00
Special Tools Required
Special Tools Required
20-108
20-108
Dashboard
Side Defogger Vent Trim Removal/
Installation
Dashboard/Steering Hanger Beam
Removal/Installation
A
B
C
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to scratch the dashboard and related
parts.
1. Insert the trim tool into a gap between the side
defogger vent trim (A) and the dashboard (B), and
release the hook (C).
2. Install the side defogger vent trim in the reverse
order of removal.
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Have an assistant help you when removing and
installing the dashboard/steering hanger beam.
• Take care not to scratch the dashboard, the body and
other related parts.
• Put on gloves to protect your hands.
1. Do the battery terminal disconnection procedure
(see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:
• Driver’s dashboard lower cover (see page
20-102)
• Driver’s dashboard undercover (see page 20-103)
• Passenger’s dashboard undercover (see page
20-104)
• Center console (see page 20-92)
• Glove box (see page 20-104)
• Kick panel, both sides (see page 20-66)
• A-pillar trim, both sides (see page 20-69)
• Steering column (see page 17-10)
• EPS control unit (see page 17-84)
08/08/21 15:02:57 61SNR030_200_0110
07AAC-SEPA240
07AAC-SEPA240
01
01
03
Driver’s side
Middle portion
20-109
Fastener Location
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
C
B
D
E
: Bolt, 1
C
E
C
C
A
B
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
C
A
3. Remove the bolt securing the under-dash fuse/
relay box (A). Disconnect the roof wire harness
connector (B), then lower the box.
4. From under the dash, disconnect the engine
compartment wire harness connectors (C), driver’s
door wire harness connectors (D), and the floor
wire harness connectors (E) from the dashboard
wire harness connectors or the under-dash fuse/
relay box.
5. Disconnect the SRS unit connector A, the antenna
connector (B), and detach the wire harness clips (C).
Remove the ground bolt (D) with a TORX T30 bit.
6. Disconnect the A/C subharness connector (A) in the
glove box opening.
Use a TORX T30 bit.
08/08/21 15:02:57 61SNR030_200_0111
04
05
Passenger’s side
20-110
Dashboard
A
A
B
C
D
E
A
C
A
C
D
D
8 x 1.25 mm
7. From under the dash, disconnect the passenger’s
door wire harness connectors (A).
8. Remove the special bolts (A) from outside the
passenger’s door.
–1 Remove the caps (B).
–2 Loosen the special bolts until they disengage
from the threads on the hanger beam sleeves
(C). Continue loosening the bolts until they
engage the inside threads of the adjusting nuts
(D). The thread lock on the special bolts makes
the special bolts and the adjusting nuts turn
together.
–3 Tighten the special bolts to turn the adjusting
nuts until they bottom in the sleeves. This
creates a gap (E) between the adjusting nuts
and the body.
–4 Loosen the special bolts to disengage them
from the adjusting nuts. Remove the special
bolts.
08/08/21 15:02:58 61SNR030_200_0112
05
07
02
20-111
A
B
C
B
C
A
21 mm (0.83 in.)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
D
D
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
B
B
D
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
C
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
Fastener Locations
: Bolt, 3
: Bolt, 1
: Bolt, 4
B
C
D
9. If necessary, remove the dashboard side cover (A).
–1 Gently pull out along the rear edge to release
the hooks (B).
–2 Gently pull out on the side cover to release the
hooks (C), then remove the side cover.
10. If the adjusting nuts (A) are not screwed fully into
the sleeve after removing the special bolts, screw
the externally threaded nuts into the sleeves with a
21 mm open-end wrench. In this case, the special
bolts should be replaced with new ones because
the thread lock is worn out.
11. Remove the caps (A), then remove the bolts
(B, C, D) from outside the driver’s door.
08/08/21 15:02:59 61SNR030_200_0113
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст