Acura CSX. Manual — part 445
01
02
SNR9A00J26220257210KDAT00
Special Tools Required
20-100
Dashboard
Subdisplay Visor Removal/Installation
Fastener Location
: Screw, 1
Fastener Locations
: Clip, 4
B, E
A
B
C
B
B
F
D
E
D
KTC trim tool set SOJATP2014
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the dashboard and related
parts.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
1. Remove the driver’s dashboard lower cover
(see page 20-102).
2. Tilt the steering column down, and pull it fully out.
3. Remove the screw.
4. Pull the back of the driver’s pocket (A) by hand from
the driver’s lower cover opening to release the clips
(B) and the hook (C) on the outside.
5. Pry up on the inside edge of the subdisplay visor
(D) with a trim tool to detach the clip (E), and
release the pin (F).
08/08/21 15:02:53 61SNR030_200_0102
07AAC-SEPA240
03
04
05
20-101
Fastener Locations
: Clip, 6
A
B
A
Fastener Locations
: Screw, 5
A
B
C
6. Detach the clips along the upper edge of the
subdisplay visor (A). Gently pull out the visor to
release the hooks (B).
7. Disconnect the illumination control switch
connector (A).
8. If necessary, remove the screws, then remove the
illumination control switch (A), and the driver’s
pocket (B) from the subdisplay visor (C).
9. Install the subdisplay visor in the reverse order of
removal, and note these items:
• Make sure the connector is plugged in properly.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
08/08/21 15:02:53 61SNR030_200_0103
01
02
SNR9A00J26220219301KDAT10
Special Tools Required
20-102
Dashboard
Driver’s Dashboard Lower Cover Removal/Installation
A
Fastener Locations
: Clip, 3
Fastener Locations
: Clip, 5
A
B
C
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to scratch the dashboard and related
parts.
1. Tilt the steering column fully upward.
2. Gently pull out on the lower edge of the dashboard
lower cover (A) to detach the lower clips.
3. Detach the upper clips, and release the hook (A)
and the pin (B) by pulling the driver’s dashboard
lower cover (C) back.
4. Install the lower cover in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
08/08/21 15:02:54 61SNR030_200_0104
07AAC-SEPA240
01
SNR9A00J26220219371KDAT10
01
SNR9A00J26220219285KDAT00
20-103
20-103
Driver’s Dashboard Undercover
Removal/Installation
Center Pocket Removal/Installation
Fastener Locations
: Clip, 2
C
D
E
A
B
Fastener Locations
: Screw, 4
A
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the driver’s dashboard undercover (A).
–1 Turn the lock knob (B) 90 °.
–2 Gently pull down the rear edge to detach the
clips.
–3 Pull the undercover away to release the pin (C)
from the holder (D).
–4 For some models: If equipped with a foot light
illumination, disconnect the foot light
illumination connector (E).
2. Install the undercover in the reverse order of
removal, and note these items:
• Make sure the foot light illumination connector is
plugged in properly (for some models).
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
NOTE: Take care not to scratch the dashboard and
related parts.
1. Disassemble the dashboard/steering hanger beam
(see page 20-114).
2. Remove the screws, then remove the center pocket
(A).
3. Install the center pocket in the reverse order of
removal.
08/08/21 15:02:54 61SNR030_200_0105
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст