Acura CSX. Manual — part 446
02
SNR9A00J26220219371KDAT20
01
02
SNR9A00J26220230101KDAT00
20-104
20-104
Dashboard
Passenger’s Dashboard Undercover
Removal/Installation
Glove Box Removal/Installation
Fastener Locations
: Clip, 2
B
: Clip, 2
C
D
F
A
E
C
C
B
B
Fastener Locations
: Bolt, 2
5 x 0.8 mm
5 N·m
(0.5 kgf·m, 4 lbf·ft)
A
B
B
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the passenger’s dashboard undercover (A).
–1 Gently pull out the rear edge to detach the clips
(B, C).
–2 Pull the undercover away to release the pins
(D) from the holders (E).
–3 For some models: If equipped with a foot light
illumination, disconnect the foot light
illumination connector (F).
2. Install the undercover in the reverse order of
removal, and note these items:
• Make sure the foot light illumination connector is
plugged in properly (for some models).
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the bolts.
2. While holding the glove box (A), release the glove
box stop (B) on each side from the dashboard by
pushing them in, then remove the glove box.
3. Install the glove box in the reverse order of
removal.
08/08/21 15:02:55 61SNR030_200_0106
01
02
SNR9A00J26220219251KDAT50
Special Tools Required
Driver’s Center Vent
20-105
Dashboard Vent Removal/Installation
Fastener Locations
A
B
: Screw, 3
Fastener Locations
A
B
: Screw, 3
KTC trim tool set SOJATP2014
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the subdisplay visor (see page 20-100).
2. Remove the screws securing the driver’s outer vent
(A), then remove the driver’s outer vent from the
subdisplay visor (B).
3. Install the outer vent in the reverse order of
removal.
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove these items:
• Navigation unit, with navigation system
– ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
• Audio unit, without navigation system
– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
2. Remove the screws securing the driver’s center
vent (A), then remove the driver’s center vent from
the center panel (B).
3. Install the center vent in the reverse order of
removal.
08/08/21 15:02:55 61SNR030_200_0107
07AAC-SEPA240
01
02
05
Passenger’s Vent
Outer
Center
20-106
Dashboard
A
B
B
A
B
C
A
B
A
C
C
C
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Take care not to scratch the dashboard and related
parts.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Put on gloves to protect your hands.
1. While holding the glove box (A), release the glove
box stops (B) on each side from the dashboard by
pushing them in.
2. From inside the glove box opening, push on the
side hooks (A) by hand to release them. Gently pull
out the side vent (B) to release the other hooks (C),
then remove the passenger’s vent.
3. Install the passenger’s vents in the reverse order of
removal.
08/08/21 15:02:56 61SNR030_200_0108
01
SNR9A00J26220230122KBAT00
01
SNR9A00J26220219359KDAT00
Special Tools Required
20-107
20-107
Glove Box Striker Replacement
Dashboard Side Trim Removal/
Installation
Fastener Locations
A
: Screw, 2
A
B
C
D
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE: Take care not to scratch the dashboard and
related parts.
1. While holding the glove box, release the glove box
stop on each side from the dashboard by pushing
them in.
2. Remove the screws, then remove the glove box
striker (A).
3. Install the striker in the reverse order of removal.
KTC trim tool set SOJATP2014
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to scratch the dashboard and related
parts.
1. Remove the dashboard side trim (A).
–1 Gently pull up the rear edge to release the rear
hooks (B).
–2 Pull the trim away to release the front hook (C)
from the A-pillar trim (D).
2. Install the side trim in the reverse order of removal.
08/08/21 15:02:56 61SNR030_200_0109
07AAC-SEPA240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст