Acura CSX. Manual — part 218
*02
Exploded View - Transmission Housing
13-100
Manual Transmission
TRANSMISSION HOUSING
32 mm SEALING CAP
34 N·m (3.5 kgf·m, 25 lbf·ft)
10 mm SEALING WASHER
FILLER PLUG
44 N·m (4.5 kgf·m, 33 lbf·ft)
40 x 56 x 8 mm OIL SEAL
10 mm FLANGE BOLT
44 N·m (4.5 kgf·m, 33 lbf·ft)
14 mm SEALING WASHER
TRANSMISSION HANGER A
8 mm FLANGE BOLT
27 N·m (2.8 kgf·m, 20 lbf·ft)
INTERLOCK BOLT
39 N·m (4.0 kgf·m, 29 lbf·ft)
OIL GUIDE PLATE M
72 mm SHIM
OIL GUTTER PLATE
DRAIN PLUG
39 N·m (4.0 kgf·m, 29 lbf·ft)
20 mm SEALING WASHER
STEEL BALL
SPRING
TRANSMISSION HANGER B
DETENT BOLT
22 N·m (2.2 kgf·m, 16 lbf·ft)
12 mm SEALING WASHER
HARNESS BRACKET A
6 x 30 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft)
8 x 14 mm DOWEL PIN
CHANGE LEVER ASSEMBLY
TRANSMISSION HANGER
10 mm FLANGE BOLT
44 N·m (4.5 kgf·m, 33 lbf·ft)
6 x 20 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft)
6 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft)
OUTPUT SHAFT (COUNTERSHAFT)
SPEED SENSOR
O-RING
80 mm SHIM
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:47:54 61SNR030_130_0102
*03
04
05
*04
13-101
C
A
A
D
E
B
C
F
D
B
A
B
A
D
D
C
B
A
B
D
C
D
D
E
F
NOTE: Place the clutch housing on two pieces of wood
thick enough to keep the mainshaft from hitting the
workbench.
1. Remove the release fork and the release bearing
(see page 12-24).
2. Remove the detent bolts (A), the 12 mm sealing
washers (B) the springs (C), the steel balls (D), and
the back-up light switch (E). Then remove the
transmission hanger (F).
3. Remove the 20 mm bolt (A) and the 20 mm sealing
washer (B).
4. Remove the interlock bolt (B), the change lever
assembly (C), the 8 x 14 mm dowel pins (D), and
harness bracket A.
5. Remove the drain plug (A), the filler plug (B), the
10 mm flange bolt (C), and the sealing washers (D).
6. Remove the output shaft (countershaft) speed
sensor (E) with the O-ring (F).
08/08/21 14:47:55 61SNR030_130_0103
*05
08
09
*06
13-102
Manual Transmission
A
B
A
D
B
C
D
D
A
B
A
7. Loosen the 8 mm flange bolts in a crisscross
pattern in several steps, then remove them with
transmission hanger A and transmission hanger B.
8. Remove the 32 mm sealing cap (A).
9. While expanding the 72 mm snap ring (B) on the
countershaft ball bearing with snap ring pliers, lift
the transmission housing (C). Release the snap ring
pliers, and remove the transmission housing and
the three 14 x 20 mm dowel pins (D).
10. Remove the reverse idler gear (A) and the reverse
idler gear shaft (B).
11. Remove the reverse shift fork (A).
08/08/21 14:47:56 61SNR030_130_0104
*07
*08
*09
13-103
D
E
B
C
F
A
A
B
M
B
A
12. Apply tape to the mainshaft splines to protect the
seal, then remove the mainshaft assembly (A) and
the countershaft assembly (B) with the shift fork
assembly (C) from the clutch housing (D).
13. Remove the 28 mm spring washer (E) and the
28 mm washer (F).
14. Remove the differential assembly (A) and the
magnet (B).
15. Remove the oil gutter plate (A), the 72 mm shim (B),
and oil guide plate M.
08/08/21 14:47:57 61SNR030_130_0105
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст