Acura CSX. Manual — part 217
21
22
23
24
13-96
Manual Transmission
12 x 1.25 mm
64 N·m (6.5 kgf·m, 47 lbf·ft)
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 9 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
9 lbf·ft)
A
B
C
A
33. Install the two upper transmission mounting bolts.
34. Install the engine harness cover (A).
35. Install the air cleaner housing mounting bracket.
36. Install the harness clips (A) on the shift cable
bracket (B) and the harness bracket (C).
08/08/21 14:47:29 61SNR030_130_0098
*07
*08
26
’06 model
’07-09 models
13-97
8 x 1.25 mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
C
B
C
A
(P/N 08C30-B0234M)
E
D
C
B
C
A
(P/N 08C30-B0234M)
8 x 1.25 mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
A
D
B
C
37. Apply a light coat of silicone grease (P/N 08C30-
B0234M) to the shift cable ends (A).
NOTE: Make sure not to get any silicone grease on
the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves
38. Install the shift cable bracket (B) and the shift cables
(C), then install new cotter pins (D) or lock pins (E).
39. Connect the back-up light switch connector (A), the
output shaft (countershaft) speed sensor connector
(B), and the reverse lockout solenoid connector (C).
Install the harness clips (D).
Replace.
08/08/21 14:47:30 61SNR030_130_0099
27
28
13-98
Manual Transmission
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
(P/N 08798-9002)
B
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
A
C
C
D
40. Apply super high temp urea grease (P/N 08798-
9002) to the end of the slave cylinder pushrod.
Install the slave cylinder (A), then install the clutch
line bracket (B). Be careful not to bend the clutch
line.
41. Install the battery base (A) with the coolant
reservoir (B).
42. Install the harness clips (C) and the intake air duct
(D).
43. Install the air cleaner assembly (see page 11-345).
44. Do the battery installation procedure (see page
22-69).
45. Install the under-cowl panel and the cowl cover
(see page 20-163).
46. Check the shift lever and the clutch operation.
47. Check the wheel alignment (see page 18-5).
48. Test-drive the vehicle.
08/08/21 14:47:31 61SNR030_130_0100
*01
SNR9AA9E34150100000LCAT00
Exploded View - Clutch Housing
13-99
Transmission Disassembly
MAINSHAFT ASSEMBLY
COUNTERSHAFT ASSEMBLY
REVERSE IDLER GEAR
BALL BEARING
REVERSE IDLER GEAR SHAFT
14 x 20 mm DOWEL PIN
MAGNET
DIFFERENTIAL ASSEMBLY
OIL GUIDE PLATE C
BEARING SET PLATE
NEEDLE BEARING
28 mm WASHER
28 mm SPRING WASHER
6 mm SPECIAL BOLT
REVERSE SHIFT FORK
SHIFT FORK ASSEMBLY
15 N·m (1.5 kgf·m, 11 lbf·ft)
72 mm SNAP RING
6 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft)
35 x 58 x 8 mm OIL SEAL
28 x 43 x 7 mm OIL SEAL
20 mm WASHER
BACK-UP LIGHT SWITCH
29 N·m (3.0 kgf·m, 22 lbf·ft)
20 mm BOLT
44 N·m (4.5 kgf·m, 33 lbf·ft)
CLUTCH HOUSING
Replace.
Replace.
Replace.
08/08/21 14:47:53 61SNR030_130_0101
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст