Acura CSX. Manual — part 305
01
02
03
SNR9AA1E10411239511KCAT00
−
−
Special Tools Required
14-298
Transmission Housing
Bearing Installation
A
B
A
B: 0
7 mm (0
0.28 in.)
A
• Attachment, 78 x 80 mm 07NAD-PX40100
• Driver 07749-0010000
• Attachment, 42 x 47 mm 07746-0010300
1. Install the bearings in the direction shown.
2. Expand each snap ring using snap ring pliers, and
install the mainshaft bearing (A) and the
countershaft bearing (B) part-way into the housing
using the driver and the 78 x 80 mm attachment.
3. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
4. Expand the snap ring of the idler gear shaft (A)
using the snap ring pliers, and install the bearing
part-way into the housing using the driver and the
42 x 47 mm attachment.
5. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
6. After installing the bearings check that the snap
rings (A) are seated in the bearing and the housing
grooves, and that the ring end gaps (B) are correct.
7. Install the idler shaft (see page 14-324).
08/08/21 14:50:18 61SNR030_140_0300
01
02
03
SNR9AA1E10411239511KCAT00
−
−
Special Tools Required
14-298
Transmission Housing
Bearing Installation
A
B
A
B: 0
7 mm (0
0.28 in.)
A
• Attachment, 78 x 80 mm 07NAD-PX40100
• Driver 07749-0010000
• Attachment, 42 x 47 mm 07746-0010300
1. Install the bearings in the direction shown.
2. Expand each snap ring using snap ring pliers, and
install the mainshaft bearing (A) and the
countershaft bearing (B) part-way into the housing
using the driver and the 78 x 80 mm attachment.
3. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
4. Expand the snap ring of the idler gear shaft (A)
using the snap ring pliers, and install the bearing
part-way into the housing using the driver and the
42 x 47 mm attachment.
5. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
6. After installing the bearings check that the snap
rings (A) are seated in the bearing and the housing
grooves, and that the ring end gaps (B) are correct.
7. Install the idler shaft (see page 14-324).
08/08/21 14:50:18 61SNR030_140_0300
01
02
03
04
SNR9AA1E10400012271KDAT00
Removal
Installation
14-299
Reverse Idler Gear Removal and Installation
A
D
B
C
A
D
C
A
B
C
F
E
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
1. Remove the bolt (A) securing the reverse idler gear
shaft holder (B).
2. Install a 5 x 0.8 mm bolt (C) in the reverse idler gear
shaft (D), and pull it to remove the reverse idler
gear shaft and the gear shaft holder together.
3. Remove the reverse idler gear (A).
1. Install the reverse idler gear in the transmission
housing.
2. Lightly coat the reverse idler gear shaft (A), the
needle bearing (B), and new O-rings (C) with
lithium grease.
3. Assemble the O-rings and the needle bearing on
the reverse idler gear shaft, then install the reverse
idler gear shaft in the reverse idler gear shaft
holder (D). Align the D-shaped cut out (E) of the
shaft with the D-shaped area (F) of the holder.
4. Install the reverse idler gear shaft/holder assembly
on the transmission housing.
08/08/21 14:51:11 61SNR030_140_0301
01
SNR9AA1E10480139301KAAT00
14-300
Valve Body
Valve Body and ATF Strainer Removal
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
A
1. Remove the ATF feed pipes (A) and the ATF joint pipes (B).
2. Remove the ATF strainer (C).
3. Remove the regulator valve body (D) (eight bolts).
4. Remove the stator shaft (E) and the stator shaft stop (F), then remove the regulator separator plate (G) and the two
dowel pins (H).
5. Remove the servo body (I) (11 bolts), then remove the servo separator plate (J) and the two dowel pins (K).
08/08/21 14:51:11 61SNR030_140_0302
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст