Acura CSX. Manual — part 426
01
SNR9A00J16166222051KBAT50
20-27
Rear Door Weatherstrip Replacement
Fastener Locations
: Bolt, 1
A
: Clip, 13
B
B
A
B
C
D
F
E
C
E
E
E
8 x 1.25 mm
29 N·m
(3.0 kgf·m, 22 lbf·ft)
: Clip, 2
C
: Clip, 1
D
(White)
(Black)
(Left: Yellow
Right: Green)
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the door.
• Remove the clips with a clip remover.
1. At the B-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door
weatherstrip (E).
3. Install the weatherstrip in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Make sure the weatherstrip is installed in the
holder (F) securely.
• Apply medium strength liquid thread lock to the
door checker mounting bolt before installation.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
• Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:10 61SNR030_200_0029
01
02
03
SNR9A00J54400020371MBAT10
Front
Rear
20-28
Doors
Front and Rear Door Glass Adjustment
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
A
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
A
A
B
NOTE: Check the weatherstrip and glass run channel for
damage or deterioration, and replace them if necessary.
1. Place the vehicle on a firm, level surface.
2. Remove these items:
• Door panel:
– Front door (see page 20-7)
– Rear door (see page 20-17)
• Plastic cover:
– Front door (see step 4 on page 20-9)
– Rear door (see step 4 on page 20-19)
3. Carefully move the glass (A) until you can see the
glass mounting bolts (B), then loosen them.
4. Push the glass against the channel (C), then tighten
the glass mounting bolts.
5. Check that the glass moves smoothly.
6. Raise the glass fully, and check for gaps. Also make
sure that the glass (A) contacts the glass run
channel (B) evenly.
08/08/21 14:59:11 61SNR030_200_0030
01
01
SNR9A00J16126700000MBAT00
Front door
20-29
20-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5 m (19 in.)
300 mm (12 in.)
B
C
A
D
8 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B
C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel:
• Front door (see page 20-9)
• Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and
on the sealing area as shown, and note these items:
• Use a 12 mm (0.47 in.) diameter hose (A).
• Adjust the rate of water flow as shown (B).
• Do not use a nozzle.
• Hold the hose about 300 mm (12 in.) away from
the door (C).
NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when
adjusting the doors.
2. Adjust at the hinges (A):
• Pad a floor jack (B) with shop towels (C), then use
the jack to support the door to prevent damage to
the door while adjusting it.
• On the front door: Remove the front inner fender
(see page 20-171). Loosen the hinge mounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
• On the rear door: Loosen the hinge mounting
bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
08/08/21 15:00:01 61SNR030_200_0031
01
01
SNR9A00J16126700000MBAT00
Front door
20-29
20-29
Front and Rear Door Position
Adjustment
12 mm (0.47 in.)
0.5 m (19 in.)
300 mm (12 in.)
B
C
A
D
8 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
F
8 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
A
B
C
7. Attach the plastic cover making sure it its sealed
around its outside perimeter to seal out water.
8. Reinstall the door panel:
• Front door (see page 20-9)
• Rear door (see page 20-19)
9. Check for water leaks. Run water over the roof and
on the sealing area as shown, and note these items:
• Use a 12 mm (0.47 in.) diameter hose (A).
• Adjust the rate of water flow as shown (B).
• Do not use a nozzle.
• Hold the hose about 300 mm (12 in.) away from
the door (C).
NOTE: Check for a flush fit with the body, then check for
equal gaps between the front, rear, and bottom door
edges and the body. Check that the door and the body
edges are parallel. If necessary, replace the mounting
bolts before adjusting the door position.
1. Place the vehicle on a firm, level surface when
adjusting the doors.
2. Adjust at the hinges (A):
• Pad a floor jack (B) with shop towels (C), then use
the jack to support the door to prevent damage to
the door while adjusting it.
• On the front door: Remove the front inner fender
(see page 20-171). Loosen the hinge mounting
bolts (D) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
• On the rear door: Loosen the hinge mounting
bolts (E) slightly, and move the door backward or
forward, up or down as necessary to equalize the
gaps.
08/08/21 15:00:01 61SNR030_200_0031
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст