Acura CSX. Manual — part 294
01
02
03
04
SNR9AA1E10411412281KBAT00
14-257
Shift Cable Replacement
A
A
B
C
A
B
C
D
E
F
1. Raise the vehicle on a lift, or apply the parking
brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
2. Move the shift lever to R.
3. Remove the center console (see page 20-92).
4. Pry the socket holder lock (A) up using a
screwdriver.
5. Remove the nut securing the shift cable end.
6. Rotate the socket holder retainer (A)
counterclockwise, push it against the socket holder
bracket (B), then slide the socket holder to remove
the shift cable (C) from the socket holder bracket.
7. Remove the three bolts securing the shift cable
holder (A), then remove the shift cable cover (B).
8. Pry up the lock tab of the lock washer (C), and
remove the lock bolt (D) and the lock washer, then
separate the control lever (E) from the selector
control shaft (F). Do not bend the shift cable
excessively.
08/08/21 14:48:52 61SNR030_140_0259
05
*01
14-258
Automatic Transmission
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
C
D
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
D
6 x 1.0 mm
14 N·m
(1.4 kgf·m,
10 lbf·ft)
A
B
E
F
C
9. Remove the nuts securing the shift cable bracket
(A) and the grommet (B).
10. Remove the shift cable grommet, and pull out the
shift cable (C).
11. Insert a new shift cable through the grommet hole
(D), and install the grommet in its hole. Do not bend
the shift cable excessively.
12. Secure the shift cable bracket and the grommet
with the nuts.
13. Make sure that the transmission is in the R position
at the selector control shaft.
14. Install the control lever (A) over the selector control
shaft (B).
15. Secure the control lever with a new lock washer (C)
and the lock bolt (D), then bend the lock tab of the
lock washer against the bolt head.
16. Install the shift cable cover (E), and install the shift
cable holder (F) on the cover.
17. Install the shift cable on the shift lever, and adjust
the cable (see step 5 on page 14-259).
Replace.
08/08/21 14:48:53 61SNR030_140_0260
01
02
03
04
SNR9AA1E10411412281MBAT00
14-259
Shift Cable Adjustment
A
A
B
C
A
B
C
1. Remove the center console (see page 20-92).
2. Pry the socket holder lock (A) up using a
screwdriver.
3. Remove the nut securing the shift cable end.
4. Rotate the socket holder retainer (A)
counterclockwise, push it against the socket holder
bracket (B), then slide the socket holder to remove
the shift cable (C) from the socket holder bracket.
5. While holding the socket holder (A), rotate the
socket holder retainer (B) fully counterclockwise,
and press in the socket holder lock (C) between the
socket holder and the socket holder retainer
enough.
08/08/21 14:48:54 61SNR030_140_0261
05
06
*01
08
14-260
Automatic Transmission
A
B
C
A
B
C
B
A
6. Align the socket holder (A) with the slot (B) in the
socket holder bracket (C), then slide the socket
holder into the socket holder bracket.
7. Rotate the socket holder retainer (A) clockwise, and
push the socket holder lock (B). Rotate the holder
retainer counterclockwise until the retainer stops at
the stop (C) of the socket holder lock to secure the
shift cable.
8. Push the shift cable (A) until it stops, then release it.
Pull the shift cable back one step so that the shift
position is in R. Do not hold the shift cable guide (B)
to adjust the shift cable.
9. Turn the ignition switch to ON (II), and check that
the R position indicator comes on.
10. Turn the ignition switch to LOCK (0).
08/08/21 14:48:55 61SNR030_140_0262
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст