Acura CSX. Manual — part 450
01
01
SNR9A00J46127053676KBAT10
Passenger’s Seat
20-120
20-120
Seats
Front Seat Frame Replacement
Fastener Locations
: Bolt, 4
10 x 1.25 mm
34 N·m
(3.5 kgf·m, 25 lbf·ft)
A
A
B
C
Fastener Locations
: Clip, 4
A
9. With the help of an assistant, carefully remove the
front seat through the front door opening.
10. Install the seat in the reverse order of removal, and
note these items:
• Apply medium strength liquid thread lock to the
seat mounting bolts before reinstallation.
• Tighten the seat mounting bolts to the specified
torque in the sequence shown. Slide the seat (A)
all the way back and tighten
and
, then slide
it forward and tighten
and
. The driver’s seat
is shown; the passenger’s seat is similar.
• Tighten the bolts by hand first, then tighten them
to specification with a torque wrench.
• Make sure each connector is plugged in properly.
• Check for any DTCs that may have been set
during repairs, and clear them.
• Do the battery terminal reconnection procedure
(see page 22-68).
Calibrate the ODS unit after any of these actions
(see page 24-27):
• Front passenger’s seat replacement (including any
seat components)
• Replacement of the front seat weight sensors
• After a vehicle collision
NOTE:
• Put on gloves to protect your hands.
• Apply oil to the pivot portions of the slide locks.
• Apply multipurpose grease to the sliding portions of
the seat tracks.
• If the side airbag has deployed, replace the seat
frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:
• Front seat-back cover (see page 20-123)
• Front seat cushion cover (see page 20-127)
• ODS unit (see page 24-209)
• Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner
covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
01
01
SNR9A00J46127053676KBAT10
Passenger’s Seat
20-120
20-120
Seats
Front Seat Frame Replacement
Fastener Locations
: Bolt, 4
10 x 1.25 mm
34 N·m
(3.5 kgf·m, 25 lbf·ft)
A
A
B
C
Fastener Locations
: Clip, 4
A
9. With the help of an assistant, carefully remove the
front seat through the front door opening.
10. Install the seat in the reverse order of removal, and
note these items:
• Apply medium strength liquid thread lock to the
seat mounting bolts before reinstallation.
• Tighten the seat mounting bolts to the specified
torque in the sequence shown. Slide the seat (A)
all the way back and tighten
and
, then slide
it forward and tighten
and
. The driver’s seat
is shown; the passenger’s seat is similar.
• Tighten the bolts by hand first, then tighten them
to specification with a torque wrench.
• Make sure each connector is plugged in properly.
• Check for any DTCs that may have been set
during repairs, and clear them.
• Do the battery terminal reconnection procedure
(see page 22-68).
Calibrate the ODS unit after any of these actions
(see page 24-27):
• Front passenger’s seat replacement (including any
seat components)
• Replacement of the front seat weight sensors
• After a vehicle collision
NOTE:
• Put on gloves to protect your hands.
• Apply oil to the pivot portions of the slide locks.
• Apply multipurpose grease to the sliding portions of
the seat tracks.
• If the side airbag has deployed, replace the seat
frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:
• Front seat-back cover (see page 20-123)
• Front seat cushion cover (see page 20-127)
• ODS unit (see page 24-209)
• Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner
covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
02
03
20-121
Fastener Locations
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
: Bolt, 4
A
B
C
A
B
C
A
(Black)
B
(White)
4. Remove the bolts, and release the seat cushion
springs (A) from the hooks (B), then remove the
seat cushion frame (C).
5. Remove the front seat weight sensors (see page
24-207).
6. If necessary, remove the bushing (A, B) from the
seat cushion frame (C).
7. Install the new seat frame in the reverse order of
removal, and note these items:
• Make sure the ODS unit connector is plugged in
properly.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
• Make sure the seat wiring harnesses are routed
properly and are not pinched.
• Calibrate the ODS unit, if necessary (see page
24-27).
08/08/21 15:03:55 61SNR030_200_0123
04
SNR9A00J46127053676KBAT20
Driver’s Seat
20-122
Seats
A
B
C
D
Fastener Locations
: Clip, 3
A
E
Check the operation of the driver’s seat position sensor
after any of these actions (see page 24-29):
• Driver’s seat position sensor replacement
• Cover plate (front side of driver’s seat slide rail)
replacement
NOTE:
• Put on gloves to protect your hands.
• Apply oil to the pivot portions of the slide lock.
• Apply multipurpose grease to the sliding portions
and pivot portions of the seat tracks.
• If the side airbag has deployed, replace the seat
frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:
• Front seat-back cover/pad (see page 20-123)
• Front seat cushion cover/pad (see page 20-127)
• Driver’s seat position sensor (see page 24-211)
• Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner
covers (A), the outer upper rail cover (B), the inner
upper rail cover (C) and the module holder (D) from
the seat frame (E).
4. Install the new seat frame in the reverse order of
removal, and note these items:
• Make sure the driver’s seat position sensor
connector is plugged in properly.
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Push the clips into place securely.
• Make sure the seat wiring harnesses are routed
properly and not pinched.
08/08/21 15:03:56 61SNR030_200_0124
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст