Acura CSX. Manual — part 451
05
06
SNR9A00J46127053950KBAT10
Special Tools Required
Passenger’s seat
Driver’s seat
20-123
Front Seat-back Cover Replacement
A
D
C
C
C
F
H
I
J
D
E
A
B
D
E
C
C
C
F
D
G
H
I
J
E
H
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
• Check the operation of the driver’s seat position
sensor after any of these actions (see page 24-29):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail)
replacement
• Calibrate the ODS unit after any of these actions
(see page 24-27):
– Front passenger’s seat replacement (including any
seat components)
– Replacement of the front seat weight sensors
– After a vehicle collision
NOTE:
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
• Take care not to tear or damage the seat covers.
• On the passenger’s seat, do not touch the OPDS
sensor in the seat-back pad, and keep it away from oil.
Oil can corrode the sensor caution it to fail.
• Put on gloves to protect your hands.
1. Remove the front seat (see page 20-118).
2. Remove the head restraint.
3. From under the seat cushion, detach the side
airbag connector clip (A). On the driver’s seat,
disconnect the seat-back heater connector (B).
4. Release the hooks (C) from the seat cushion frame
spring (D). Remove the wire ties (E), and pull the
side airbag harness (F) and the seat-back heater
harness (G) (driver’s seat) out through the slits (H)
in the seat cushion cover (I). Turn over the seat
cushion cover, and release the hooks (J).
08/08/21 15:03:56 61SNR030_200_0125
07AAC-SEPA240
07
08
09
10
20-124
Seats
Fastener Locations
: Clip, 2
A
C
B
A
A
D
C
A
B
A
E
B
C
A
B
C
D
A
B
A
A
A
A
5. Detach the clips and the hooks (A) by pulling out
the bottom of the back cover (B), then gently pull
down the panel to release the hooks (C) from the
seat frame, and remove the cover.
6. Pull the side airbag harness (A) out through the
loop (B), and release the Velcro fastener (C) and the
hooks (D), then pull the seat-back cover (E) back.
7. Detach the harness clip (A), and pull the side airbag
harness (B) and seat-back heater harness (C)
(driver’s seat) out through the harness holes (D) in
the seat-back cover and seat frame. Driver’s seat is
shown; passenger’s seat is similar.
8. Remove the side airbag (see page 24-191).
9. Release the hook strips (A), then loosen the seat-
back cover (B). Driver’s seat is shown; passenger’s
seat is similar.
08/08/21 15:03:57 61SNR030_200_0126
11
02
13
01
’06-07 models
’08-09 model
20-125
A
B
C
B
A
B
C
E
F
G
H
D
A
A
10. Turn over the reinforcing cloth (A), then release the
hooks (B) from the side airbag module holder (C).
Passenger’s seat is shown; driver’s seat is similar.
11. Passenger’s seat: Disconnect the OPDS sensor
connectors (A) and the ODS unit subharness
connector (B) from the ODS unit (C), and pull them
in through the hole in the seat frame. Pull the ODS
unit subharness (D) out through the harness hole
(E) in the seat-back cover (F). Detach the harness
clips (G), and remove the wire tie (H).
12. Pinch the tabs on the ends of the head restraint
guides (A), and remove them from the seat-back.
08/08/21 15:03:58 61SNR030_200_0127
14
15
16
17
20-126
Seats
A
B
A
A
A
A
A
A
B
C
D
13. Remove the seat-back cover/pad (A) from the seat
frame (B).
14. Pull back the edge of the seat-back cover all the
way around, and release the clips (A), then remove
the seat-back cover.
15. Install the cover in the reverse order of removal,
and note these items:
• Reinitialize the ODS unit (see page 24-26).
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the clips, the hooks,
and the hook strips.
• Replace any clips (A) you removed with new
ones.
• Before installing the side airbag (B), make sure
the reinforcing cloth (C) is fixed on the seat-back
frame (D) securely.
• Make sure the side airbag harness, and the seat
heater harness (some driver’s seat) or the ODS
unit subharness (passenger’s seat) are routed
properly.
08/08/21 15:03:59 61SNR030_200_0128
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст