Acura CSX. Manual — part 449
*01
SNR9A00J46100000000DAAT00
20-116
Seats
Component Location Index
REAR SEAT
FRONT SEAT
(Driver’s)
FRONT SEAT
(Passenger’s)
Removal/Installation, page 20-131
Seat-back Latch Replacement, page 20-135
Seat-back Release Lever/Cable
Removal/Installation, page 20-136
Armrest Beverage Holder
Replacement, page 20-137
Armrest Replacement, page 20-138
Seat-back Cover Replacement, page 20-139
Seat Side Bolster Cover Replacement, page 20-143
Seat Cushion Cover Replacement, page 20-143
Armrest Cover Replacement, page 20-144
Active Head Restraint Inspection, page 20-117
Removal/Installation, page 20-118
Seat Frame Replacement, page 20-122
Seat-back Cover Replacement, page 20-123
Seat Cushion Cover Replacement, page 20-127
Active Head Restraint Inspection, page 20-117
Removal/Installation, page 20-118
Seat Frame Replacement, page 20-120
Seat-back Cover Replacement, page 20-123
Seat Cushion Cover Replacement, page 20-127
08/08/21 15:03:05 61SNR030_200_0118
01
02
03
SNR9A00J46127031221MAAT00
Resetting Head Restraint Position
Inspection
20-117
Front Seat Active Head Restraint Inspection
A
B
Locked
B
B
B
Full stroke
Normal
250 mm
(9.84 in.)
A
B
C
D
250 mm
(9.84 in.)
Above 50 mm (2.0 in.)
(Level)
A
NOTE: If the vehicle has been in a collision, always
inspect the active head restraint, even if they appear
reusable, by doing the following procedure.
1. Push the head restraint (A) forward fully from the
locked position to release the inertial lock (B).
2. Slowly raise the head restraint into the normal
position.
3. Fold the seat-back forward, then recline the seat-
back to the first lock position, and adjust the head
restraint to the highest position.
4. Apply masking tape on the top of the head restraint.
5. Make marks (A) on both sides at 250 mm (9.84 in.)
upward from the roots of the head restraint frame
(B) along the back of the head restraint (C) surface.
Make a center of these points as a datum point (D).
6. Push the head restraint (A) forward, and measure
the level amount of the head restraint movement.
The head restraint should move than 50 mm (2.0 in.)
without resistance. If it is less than 50 mm (0.2 in.),
or the head restraint does not move smoothly,
replace the seat frame assembly:
• Passenger’s seat (see page 20-120)
• Driver’s seat (see page 20-122)
08/08/21 15:03:06 61SNR030_200_0119
01
02
03
SNR9A00J46127053901KDAT00
Special Tools Required
20-118
Seats
Front Seat Removal/Installation
A
A
7/16-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
A
B
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
• Put on gloves to protect your hands.
• When prying with a flat-tip screwdriver, wrap it with
protective tape to prevent damage.
• Take care not to scratch the body or tear the seat
covers.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
1. Do the battery terminal disconnection procedure
(see page 22-68), and wait at least 3 minutes before
beginning work.
2. Tilt the steering wheel all the way up, and push it
all the way in. Adjust the seat-back recline to a
middle position.
3. Slide the front seat forward fully. Carefully pry up
on the bottom edge of the anchor cover (A) to
release the hooks, and remove the cover.
4. Remove the lower anchor bolt (A).
5. Remove the seat track outer end covers (A) and the
seat track center end covers (B) from the back of
both seat tracks.
08/08/21 15:03:07 61SNR030_200_0120
07AAC-SEPA240
05
04
06
07
Passenger’s seat
Driver’s seat
20-119
Fastener Locations
: Bolt, 2
10 x 1.25 mm
Fastener Locations
: Bolt, 2
10 x 1.25 mm
A
B
C
D
F
A
A
B
C
D
E
A
6. Remove the rear seat track bolts.
7. Slide the front seat rearward fully, and remove the
front seat track bolts.
8. Lift up the front seat, then detach the harness clips
(A), and disconnect the side airbag connector (B),
the seat belt switch connector (C), and the seat belt
buckle tensioner connector (D). On the driver’s seat,
disconnect the seat heater subharness connector
(E) or the seat position sensor connector. On the
passenger’s seat, disconnect the seat heater
subharness connector (F) or the ODS unit
subharness connector.
08/08/21 15:03:54 61SNR030_200_0121
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст