Acura CSX. Manual — part 533
01
SNR9A00J32100037301KBAT02
01
02
SNR9AGFJ32113331601KBAT01
License Plate Light: 5 W
High Mount Brake Light: 21 W
Except TYPE S model
22-180
22-180
Exterior Lights
License Plate Light Replacement
High Mount Brake Light
Replacement
A
B
C
A
B
C
A
1. Open the trunk lid, and remove the rear license trim
(see page 20-168).
2. Disconnect the 2P connector (A) from the license
plate light.
3. Release the bulb socket (B) from the lens (C) by
pressing on the tabs.
4. Remove the lens from the trunk lid by pressing on
the tabs.
5. Install the license plate light in the reverse order of
removal.
1. Open the trunk lid.
2. Disconnect the 2P connector (A) from the high
mount brake light.
3. Turn the bulb socket (B) 45 ° counterclockwise to
remove the bulb (C).
4. Remove the rear shelf (see page 20-78).
5. Remove the high mount brake light (A).
6. Install the high mount brake light in the reverse
order of removal.
08/08/21 14:27:41 61SNR030_220_0182
01
SNR9AGCJ32113331601KBAT01
*01
SNR9A00J32113314805FEAT00
TYPE S model
22-181
22-181
Brake Pedal Position Switch Test
A
B
A
B
1. Remove the two screws from the high mount brake
light (A).
2. Disconnect the terminals (B) and remove the high
mount brake light.
3. Install the high mount brake light in the reverse
order of removal.
1. Disconnect the 4P connector (A) from the brake
pedal position switch (B).
2. Check for continuity between terminals No. 1 and
No. 2.
• There should be continuity when the brake pedal
is pressed.
• There should be no continuity when the brake
pedal is released.
3. Check for continuity between terminals No. 3 and
No. 4 (with cruise control).
• There should be no continuity when the brake
pedal is pressed.
• There should be continuity when the brake pedal
is released.
4. If necessary, adjust or replace the switch, or adjust
the pedal height (see page 19-6).
08/08/21 14:27:41 61SNR030_220_0183
01
SNR9AGCJ32113331601KBAT01
*01
SNR9A00J32113314805FEAT00
TYPE S model
22-181
22-181
Brake Pedal Position Switch Test
A
B
A
B
1. Remove the two screws from the high mount brake
light (A).
2. Disconnect the terminals (B) and remove the high
mount brake light.
3. Install the high mount brake light in the reverse
order of removal.
1. Disconnect the 4P connector (A) from the brake
pedal position switch (B).
2. Check for continuity between terminals No. 1 and
No. 2.
• There should be continuity when the brake pedal
is pressed.
• There should be no continuity when the brake
pedal is released.
3. Check for continuity between terminals No. 3 and
No. 4 (with cruise control).
• There should be no continuity when the brake
pedal is pressed.
• There should be continuity when the brake pedal
is released.
4. If necessary, adjust or replace the switch, or adjust
the pedal height (see page 19-6).
08/08/21 14:27:41 61SNR030_220_0183
*01
SNR9A00J32173600000DAAT00
22-182
Turn Signal/Hazard Warning Lights
Component Location Index
HAZARD WARNING SWITCH
TURN SIGNAL INDICATORS
TURN SIGNAL SWITCH
(Built into the combination switch)
MICU
(Built into the under-dash fuse/relay box)
Test/Replacement, page 22-192
Test/Replacement, page 22-166
Input Test, page 22-188
08/08/21 14:27:42 61SNR030_220_0184
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст