Acura RSX Honda Integra. Manual — part 331
02
03
*02
04
Inspection
17-17
A
C
B
A
B
14. Check the pressure control valve for wear, burrs,
and other damage to the edges of the grooves in
the valve.
15. Inspect the bore of the pressure control valve on
the pump housing for scratches and wear.
16. Slip the pressure control valve back in the pump
housing, and check that it moves in and out
smoothly. If OK, go to step 17; if not, replace the
pump as an assembly. The pressure control valve
is not available separately.
17. Attach a hose (A) to the end of the pressure control
valve (B) as shown. Then submerge the pressure
control valve in a container of power steering fluid
or solvent (C), and blow in the hose.
• If air bubbles leak through the valve at less than
98 kPa (1.0 kgf/cm , 14.2 psi), replace the pump
as an assembly. The pressure control valve is not
available separately.
• If the pressure control valve is OK, set it aside for
reassembly later.
18. Inspect the ball bearing by rotating the outer race
slowly. If you feel any play (axial or radial) or
roughness, remove the faulty ball bearing (A), and
install a new one (B).
19. Inspect each part shown with an asterisk in the
Exploded View; if any of them are worn or
damaged, replace the pump as an assembly.
(cont’d)
2
05/06/27 18:14:25 61S6M040_170_0018
04
05
06
07
Reassembly
17-18
Power Steering
Pump Overhaul (cont’d)
B
A
07749-0010000
07746-0010100
C
B
A
A
B
C
A
B
20. Install the new pump seal (A) (with its grooved side
facing in) into the pump housing (B) by hand first,
then drive it in using the special tools until there is
no step at the top of the pump seal, and the seal is
fully seated in the pump housing.
21. Position the pump drive shaft (A) in the pump
housing, then press it in with the appropriate size
socket wrench (B) as shown. Do not apply more
than 1,370 N (140 kgf, 308 lbf) of pressure.
22. Install the 40 mm snap ring (C) with its radiused
side facing out.
23. Coat the new 23.8 mm O-ring (A) with power
steering fluid, then position it on the bottom (B) of
the pump housing.
24. Coat the new cover seal (A), cover seal (B) with
power steering fluid, then position them into the
grooves on the cover (C).
05/06/27 18:14:26 61S6M040_170_0019
08
09
10
17-19
A
C
D
B
F
E
G
C
D
E
A
B
A
C
D
B
25. Install the outer case (A) by aligning the slot (B)
inside the outer case with the cover roll pin hole (C).
Be sure that the slit (D) on the outer case is in the
direction shown.
26. Apply power steering fluid to the rubber seal (E)
(black), and install it in the slot (F) of the outer case.
27. Apply power steering fluid to the slipper seal (G)
(white), and install it on top of the rubber seal you
just installed.
28. Install the cam ring (A) by aligning the slot (B) with
the slot (C) in the outer case.
29. Insert the roll pin (D) into the slots between the cam
ring and outer case, then push the roll pin into the
set hole (E).
30. Install the rotor (A) in the cam ring (B).
31. Set the 11 vanes (C) in the grooves in the rotor.
Make sure that the round ends (D) of the vanes are
in contact with the sliding surface of the cam ring.
(cont’d)
05/06/27 18:14:26 61S6M040_170_0020
11
02
13
14
17-20
Power Steering
Pump Overhaul (cont’d)
B
A
C
D
A
B
8 x 1.25 mm
20 N·m
(2.0 kgf·m,
14 lbf·ft)
A
B
A
32. Place the side plate (A) on the cam ring, and align
the roll pin set hole (B) in the side plate with the roll
pin end (C).
33. Coat the new 51 mm O-ring (D) with power steering
fluid, then position it into the groove on the side
plate.
34. Install the pump housing (A) over the cover
assembly (B).
35. Align the bolt holes in the cover (A) with the
threaded holes in the pump housing. Install the
flange bolts loosely first, then torque the flange
bolts in a criss cross pattern in two or more steps.
36. Push in the cam ring (A) from the pump housing
cap hole (B) with a flat blade screwdriver, to make
sure the cam ring is fully seated against the outer
case.
05/06/27 18:15:06 61S6M040_170_0021
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст