Acura RSX Honda Integra. Manual — part 332
05
16
04
03
17-21
C
29 N·m (3.0 kgf·m, 22 lbf·ft)
B
A
B
A
C
D
49 N·m
(5.0 kgf·m,
36 lbf·ft)
B
6 x 1.0 mm
11 N·m
(1.1 kgf·m, 8.0 lbf·ft)
A
07ZAB-S5A0100
A
B
64 N·m
(6.5 kgf·m, 47 lbf·ft)
C
37. Install the pump preload spring (A) in the pump
housing.
38. Coat the new 12.7 mm O-ring (B) with power
steering fluid, and install it on the pump housing
cap (C).
39. Install the pump housing cap on the pump housing,
and tighten it to the specified torque.
40. Install the pressure control valve spring (A) in the
pump housing.
41. Coat the pressure control valve (B) with power
steering fluid, and install it on the pump housing.
42. Coat the new 16.7 mm O-ring (C) with power
steering fluid, and install it on the flow control
valve cap (D).
43. Install the flow control valve cap on the pump
housing, and tighten it to the specified torque.
44. Coat the new 13 mm O-ring (A) with power steering
fluid, and install it on the inlet joint (B).
45. Install the inlet joint on the pump housing.
46. Install the pulley (A), then loosely install the pulley
nut (B). Hold the power steering pump in a vise
with soft jaws (C). Be careful not to damage the
pump housing with the jaws of the vise.
47. Hold the pulley with the special tool, and tighten
the pulley nut to the specified torque.
48. Check that the pump turns smoothly by turning the
pulley. If it turns hard, loosen the four flange bolts
on the cover, then try retightening them in the
same manner as in the step 35.
49. Reinstall the power steering pump (see page 17-14).
05/06/27 18:15:07 61S6M040_170_0022
01
02
03
S6M6A00F00000057161KAAT00
17-22
Power Steering
Steering Wheel Removal
A
B
D
A
C
B
SRS components are located in this area. Review the
SRS component locations (see page 23-10) and
precautions and procedures (see page 23-11) before
performing repairs or service.
1. Make sure you have the anti-theft code for the radio,
then write down the radio station presets.
2. Disconnect the negative cable from the battery.
3. Align the front wheels straight ahead, then remove
the driver’s airbag from the steering wheel
(see page 23-130).
4. Disconnect the cruise control main switch
connector (A), and loosen the steering wheel bolt
(B).
5. Install a commercially available steering wheel
puller (A) on the steering wheel (B). Free the
steering wheel from the steering column shaft by
turning the pressure bolt (C) of the puller.
Note these items when removing the steering
wheel:
• Do not tap on the steering wheel or the steering
column shaft when removing the steering wheel.
• If you thread the puller bolts (D) into the wheel
hub more than five threads, the bolts will hit the
cable reel and damage it. To prevent this, install
a pair of jam nuts five threads up on each puller
bolt.
6. Remove the steering wheel puller, then remove the
steering wheel bolt and steering wheel from the
steering column.
05/06/27 18:15:07 61S6M040_170_0023
*01
S6M6A00F00000057161MFAT00
17-23
Steering Wheel Disassembly/Reassembly
HORN PLATE
STEERING WHEEL
ACCESS PANEL
HORN PLATE COVER
CRUISE CONTROL MAIN SWITCH
STEERING WHEEL
REAR COVER
ACCESS PANEL
05/06/27 18:15:08 61S6M040_170_0024
01
*01
03
S6M6A00F00000057161KCAT00
17-24
Power Steering
Steering Wheel Installation
A
B
B
A
C
D
A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
1. Before installing the steering wheel, make sure the
front wheels are aligned straight ahead, then center
the cable reel (A). Do this by first rotating the cable
reel clockwise until it stops. Then rotate it
counterclockwise about two and a half turns. The
arrow mark (B) on the cable reel label should point
straight up.
2. Position the two tabs (A) of the turn signal
canceling sleeve (B) as shown, and install the
steering wheel on to the steering column shaft,
making sure the steering wheel hub (C) engages
the pins (D) of the cable reel and tabs of the turn
signal canceling sleeve. Do not tap on the steering
wheel or steering column shaft when installing the
steering wheel.
3. Install the steering wheel bolt (A) and tighten it.
4. Connect the cruise control main switch connector.
5. Install the driver’s airbag, and confirm that the
system is operating properly (see page 23-131).
6. Check the horn and turn signal canceling for proper
operation.
7. Reconnect the battery and do the following:
• Power window control unit resetting procedure
(see page 22-148).
• ECM/PCM idle learn procedure (see page 11-349).
• Enter the anti-theft code for the radio, then enter
the customer’s radio station presets.
• Set the clock.
05/06/27 18:15:08 61S6M040_170_0025
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст