Acura RSX Honda Integra. Manual — part 318
12
13
*01
14-398
Transmission End Cover
End Cover Installation (cont’d)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
D
A
B
C
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
A
C
D
B
E
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
F
F
E
D
B, C
A
26. Connect the transmission range switch connector
(A) securely, then install the harness clamps (B) on
the clamp bracket (C).
27. Install the transmission range switch cover (D).
28. Install the new gasket (A) on the transmission
housing, and install the ATF pipe (B) and ATF joint
pipes (C).
29. Install the new O-rings (D) over the ATF joint pipes.
30. Install the A/T clutch pressure control solenoid
valve A (E).
31. Install the new gasket (A) on the transmission
housing, and install the ATF joint pipes (D).
32. Install the new O-rings (E) over the ATF joint pipes.
33. Install the A/T clutch pressure control solenoid
valves B and C, and harness clamp brackets (F).
05/06/27 17:59:59 61S6M040_140_0399
02
15
14-399
A
C
F
E
D
12 x 1.25mm
28 N·m
(2.9 kgf·m,
21 lbf·ft)
6 x 1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
12 x 1.25mm
28 N·m (2.9 kgf·m, 21 lbf·ft)
B
B
A
E
C
D
34. Install the ATF cooler inlet line (A) with the new
sealing washers (B), and install the bracket (C) of
the ATF cooler inlet line on the shift solenoid valve
cover hole (D) in Shaft Assembly and Housing
Installation (see step 22 on page 14-393).
35. Install the ATF cooler outlet line (E) with the new
sealing washers (F).
36. Install the breather tube (A) with facing the dot (B)
on the tube in a rearward position (differential side),
then install the other end (C) in the slot (D) of the
transmission hanger (E).
37. Install the ATF dipstick.
05/06/27 18:00:00 61S6M040_140_0400
*01
S6M6A02E10411600000DAAT00
01
S6M6A02E10411619621MAAT00
−
−
Standard: 0.05
0.15 mm (0.002
0.006 in.)
14-400
14-400
A/T Differential
Component Location Index
Backlash Inspection
THRUST SHIM, 76 mm
THRUST WASHER, 76.2 mm
BEARING OUTER RACE
CARRIER BEARING
FINAL DRIVEN GEAR
DIFFERENTIAL CARRIER
CARRIER BEARING
THRUST WASHER, 80 mm
BEARING OUTER RACE
B
A
A
1. Install the driveshaft and intermediate shaft on the
differential, then place the axles on V-blocks.
2. Check the backlash of the pinion gears (A) with a
dial indicator (B).
3. If the backlash is out of standard, replace the
differential carrier.
Selection, page 14-405
Replacement, page 14-403
Replacement, page 14-401
Replacement,
page 14-401
Backlash Inspection,
page 14-400
Replacement, page 14-401
Replacement, page 14-401
Replacement, page 14-403
05/06/27 18:00:01 61S6M040_140_0401
01
02
S6M6A02E10411619611KBAT00
01
S6M6A02E10411619621KBAT10
Special Tools Required
14-401
14-401
Carrier Bearing Replacement
Differential Carrier, Final Driven
Gear Replacement
B
C
D
A
07LAD-PW50601
10 x 1.0 mm
103 N·m
(10.5 kgf·m,
75.9 lbf·ft)
A
B
Attachment, 40 x 50 mm 07LAD-PW50601
NOTE:
• The bearing and bearing outer race should be
replaced as a set.
• Inspect and adjust the carrier bearing preload
whenever bearing is replaced.
• Check the bearing for wear and rough rotation. If the
bearing is OK, removal is not necessary.
1. Remove the carrier bearing (A) with a commercially
available puller (B), bearing separator (C), and
stopper adapter (D).
2. Install the new bearings with the special tool using
the small end and a press until it bottoms. Press the
bearing on securely so there is no clearance
between the bearing and the differential carrier.
1. Remove the final driven gear from the differential
carrier, and replace the differential carrier or final
driven gear.
2. Install the final driven gear (A) in the direction
shown on the differential carrier (B).
NOTE: Differential carrier bolts have left-hand
threads.
05/06/27 18:00:02 61S6M040_140_0402
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст