Acura RSX Honda Integra. Manual — part 319
01
02
03
04
S6M6A02E10411619631KBAT00
Special Tools Required
14-402
A/T Differential
Oil Seal Replacement
07749-0010000
07947-SD90101
A
07749-0010000
07JAD-PH80101
A
• Driver 07749-0010000
• Oil seal driver attachment 07947-SD90101
• Oil seal driver attachment 07JAD-PH80101
1. Remove the oil seal from the transmission housing.
2. Remove the oil seal from the torque converter
housing.
3. Install the new oil seal (A) in the transmission
housing with the special tools.
4. Install the new oil seal (A) in the torque converter
housing with the special tools.
05/06/27 18:00:02 61S6M040_140_0403
01
02
03
S6M6A02E10411619601KBAT00
Special Tools Required
14-403
Carrier Bearing Outer Race Replacement
E
D
C
B
A
A
B
C
07749-0010000
07GAD-SD40101
• Driver 07749-0010000
• Attachment, 78 x 90 mm 07GAD-SD40101
• Attachment, 72 x 75 mm 07746-0010600
NOTE:
• The bearing and bearing outer race should be
replaced as a set.
• Replace the bearing with a new one whenever the
outer race is replaced.
• Do not use the thrust shim on the torque converter
housing.
• Adjust bearing preload after replacing the bearing
and outer race.
• Coat all parts with ATF during installation.
1. Remove the bearing outer race (A), 76.2 mm thrust
washer (B), and 76 mm thrust shim (C) from the
transmission housing (D) by heating the housing to
about 212 °F (100 °C) with heat gun (E). Do not heat
the housing in excess of 212 °F (100 °C).
NOTE: Let the transmission housing cool to room
temperature before installing the bearing outer
race.
2. Remove the bearing outer race (A) and 80 mm
thrust washer (B) from the torque converter
housing (C).
3. Install the 80 mm thrust washer and the new
bearing outer race in the torque converter housing.
4. Drive the bearing outer race to install securely in
the housing with the special tools.
(cont’d)
05/06/27 18:00:03 61S6M040_140_0404
04
05
14-404
A/T Differential
Carrier Bearing Outer Race Replacement (cont’d)
C
B
A
D
07749-0010000
07746-0010600
5. Install the 76 mm thrust shim (A), 76.2 mm thrust
washer (B), and the new bearing outer race (C) in
the transmission housing (D).
6. Drive the bearing outer race in securely so there is
no clearance between the outer race, thrust washer,
shim, and housing with the special tools.
05/06/27 18:00:03 61S6M040_140_0405
01
02
03
S6M6A02E10411619611MAAT00
Special Tools Required
14-405
Carrier Bearing Preload Inspection
E
D
C
B
A
D
C
A
B
07749-0010000
07746-0010600
• Driver 07749-0010000
• Attachment, 72 x 75 mm 07746-0010600
• Preload inspection tool 07HAJ-PK40201
NOTE:
• If the transmission housing, torque converter housing,
differential carrier, carrier bearing and outer race, or
thrust shim were replaced, the bearing preload must
be adjusted.
• Coat all parts with ATF during installation.
• Do not use the thrust shim in the torque converter
housing.
1. Remove the bearing outer race (A), 76.2 mm thrust
washer (B), and 76 mm thrust shim (C) from the
transmission housing (D) by heating the housing to
about 212 °F (100 °C) with heat gun (E). Do not heat
the housing in excess of 212 °F (100 °C).
NOTE: Let the transmission housing cool to room
temperature before adjusting the bearing preload.
2. Install the 76 mm thrust shim of 2.6 mm (0.102 in.)
in thickness (P/N 41449-PK4-000) (A) in the
transmission housing (B).
3. Install the 76.2 mm thrust washer (C) and the
bearing outer race (D) in the transmission housing.
4. Drive the bearing outer race in securely so there is
no clearance between the outer race, thrust washer,
shim, and housing with the special tools.
(cont’d)
05/06/27 18:00:03 61S6M040_140_0406
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст