Acura RSX Honda Integra. Manual — part 477
01
01
02
S6M6A00K79100081021FAAT20
−
−
−
−
DTC 2-1:
Special Tools Required
YES
NO
YES
NO
23-40
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
A
Open or Increased Resistance in
Front Passenger’s Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the dashboard wire harness (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Open or increased resistance in the front
passenger’s airbag inflator; replace the front
passenger’s airbag (see page 23-132).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 4P connector (A)
from the cable reel.
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
Does the SRS indicator stay on?
Is DT C 2-1 indicated?
05/06/27 18:08:46 61S6M040_230_0040
−
01
*01
01
S6M6A00K79100081023FAAT00
−
−
−
−
YES
NO
Special Tools Required
YES
NO
DTC 2-3:
23-41
23-41
A
SRS UNIT CONNECTOR A (18P)
A
07XAZ-SZ30100
07SAZ-TB4011A
12. Disconnect SRS unit connector A (18P) from the
SRS unit. Do not disconnect the simulator lead
from the dashboard wire harness.
13. Check resistance between the No. 4 and No. 13
terminals and between the No. 5 and No. 14
terminals of SRS unit connector A (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor connection at the
SRS unit connector A (18P). Check the connection;
if the connection is OK, replace the SRS unit
(see page 23-141).
Open or increased resistance in the
dashboard wire harness; replace the dashboard
wire harness.
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Troubleshooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the dashboard wire harness (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
(cont’d)
Short to Another Wire or Decreased
Resistance in Front Passenger’s Airbag
Inflator
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Does the SRS indicator stay on?
05/06/27 18:09:14 61S6M040_230_0041
01
03
01
*01
−
−
−
−
YES
NO
YES
NO
23-42
SRS
DTC Troubleshooting (cont’d)
A
A
B
A
SRS UNIT CONNECTOR A (18P)
8. Read the DTC.
Go to step 9.
Short in the front passenger’s airbag inflator;
replace the front passenger’s airbag (see page
23-132).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 4P connector (A)
from the cable reel.
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness 2P connectors (B).
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the simulator lead from the dashboard
wire harness 4P connector.
14. Check resistance between the No. 4 and No. 13
terminals and between the No. 5 and No. 14
terminals of SRS unit connector A (18P). There
should be an open circuit or at least 1 M
.
Faulty SRS unit; replace the SRS unit
(see page 23-141).
Short in the dashboard wire harness; replace
the dashboard wire harness.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C 2-3 indicated?
Is the r esistance as specif ied?
05/06/27 18:09:15 61S6M040_230_0042
01
01
02
S6M6A00K79100081024FAAT00
−
−
−
−
DTC 2-4:
Special Tools Required
YES
NO
YES
NO
23-43
A
07XAZ-SZ30100
07SAZ-TB4011A
A
A
Short to Power in Front Passenger’s
Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-23).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 23-24). If another DTC is indicated, go to
the DTC Trouble shooting Index.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the dashboard wire harness (A).
5. Connect the SRS inflator simulator (2
connectors) and the simulator lead F to the
dashboard wire harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
Go to step 9.
Short to power in the front passenger’s airbag
inflator; replace the front passenger’s airbag
(see page 23-132).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 4P connector (A)
from the cable reel.
11. Disconnect both seat belt tensioner 2P connectors
(A) from the floor wire harness.
(cont’d)
Does the SRS indicator stay on?
Is DT C 2-4 indicated?
05/06/27 18:09:15 61S6M040_230_0043
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст