Acura RSX Honda Integra. Manual — part 120
S6M6AALK72100090339FAAT00
−
−
−
−
−
−
−
−
−
−
DTC P0339:
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
11-186
PGM-FI System
DTC Troubleshooting (cont’d)
CKP Sensor Circuit Intermittent
Interruption
(2005-2006 models)
1. Record all freeze data and on-board snapshots with
the HDS.
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle for 10 seconds.
4. Check the CKP NOISE COUNT in the DATA LIST
with the HDS.
Go to step 7.
Go to step 5.
5. Test-drive the vehicle for several minutes in the
range of these recorded freeze data parameters:
• Engine speed
• Vehicle speed
6. Check the CKP NOISE COUNT in the DATA LIST
with the HDS.
Go to step 7.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the CKP sensor and the ECM/PCM.
7. Check for poor or loose connections and terminals
at the following:
• CKP sensor
• ECM/PCM
• Engine ground
• Body ground
Go to step 8.
Repair the connectors or terminals, then go to
step 11.
8. Remove the cam chain case (see page 6-14), and
check the CKP sensor pulse plate for damage.
Replace the CKP sensor pulse plate, then go
to step 11.
Go to step 9.
9. Turn the ignition switch OFF.
10. Replace the CKP sensor (see page 11-280).
11. Turn the ignition switch ON (II).
12. Reset the ECM/PCM with the HDS.
13. Clear the CKP pattern with the HDS.
14. Do the ECM/PCM idle learn procedure (see page
11-349).
15. Do the CKP pattern learn procedure (see page 11-5).
16. Start the engine, and let it idle for 10 seconds.
17. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0339 is indicated, check for poor
connections or loose terminals at the CKP sensor
and the ECM/PCM, then go to step 1. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Troubleshooting is complete.
Ar e 0 counts indicated?
Ar e 0 counts indicated?
Ar e the connections and ter minals OK ?
Is the pulse plate damaged?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:35:46 61S6M040_110_0186
01
*01
S6M6AACK72100090365FAAT10
−
−
−
−
−
−
DTC P0365:
DTC P0369:
DTC P1361:
DTC P1362:
YES
NO
YES
NO
YES
NO
11-187
CMP SENSOR B 3P CONNECTOR
IGP
(YEL/BLK)
CMP SENSOR B 3P CONNECTOR
CMPB (GRN)
CMP Sensor B No Signal
(2004 model)
CMP Sensor B Circuit Intermittent
Interruption
(2004 model)
CMP Sensor B Circuit Intermittent
Interruption
(2002-2003 models)
CMP Sensor B No Signal
(2002-2003 models)
NOTE:
• Information marked with an asterisk ( ) applies to
2004 model.
• Information marked with double asterisk (
) applies
to 2002-2003 models.
1. Reset the ECM/PCM (see page 11-4).
2. Start the engine.
Go to step 3.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
CMP sensor B and the ECM/PCM.
3. Turn the ignition switch OFF.
4. Disconnect the CMP sensor B 3P connector.
5. Turn the ignition switch ON (II).
6. Measure voltage between CMP sensor B 3P
connector terminal No. 3 and body ground.
Go to step 7.
Repair open in the wire between PGM-FI main
relay 1 (FI MAIN) and CMP sensor B.
7. Measure voltage between CMP sensor B 3P
connector terminal No. 1 and body ground.
Go to step 8.
Go to step 10.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is DT C P1361
( P0365) and/ or P1362
( P0369) indicated?
Is ther e batter y voltage?
Is ther e about 5 V ?
05/06/27 17:35:47 61S6M040_110_0187
03
*02
*03
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-188
PGM-FI System
DTC Troubleshooting (cont’d)
CMP SENSOR B 3P CONNECTOR
LG1
(BRN/YEL)
IGP
(YEL/BLK)
ECM/PCM CONNECTOR A (31P)
CMPB (GRN)
ECM/PCM CONNECTOR A (31P)
CMPB (GRN)
8. Measure voltage between CMP sensor B 3P
connector terminals No. 2 and No. 3.
Go to step 9.
Repair open in the wire between CMP
sensor B and G101.
9. Substitute a known-good CMP sensor B and
recheck.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Replace original CMP sensor B (see page
11-281).
10. Measure voltage between ECM/PCM connector
terminal A26 and body ground.
Repair open in the wire between the ECM/
PCM (A26) and CMP sensor B.
Go to step 11.
11. Turn the ignition switch OFF.
12. Disconnect ECM/PCM connector A (31P).
13. Check for continuity between ECM/PCM connector
terminal A26 and body ground.
Repair short in the wire between the ECM/
PCM (A26) and CMP sensor B.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is DT C P1361
( P0365) and/ or
P1362
( P0369) indicated?
Is ther e about 5 V ?
Is ther e continuity?
05/06/27 17:35:47 61S6M040_110_0188
01
*01
03
S6M6AALK72100090365FAAT10
−
−
−
−
−
−
−
−
DTC P0365:
YES
NO
YES
NO
YES
NO
YES
NO
11-189
CMP SENSOR B 3P CONNECTOR
IGP
(YEL/BLK)
CMPB
(GRN)
CMP SENSOR B 3P CONNECTOR
IGP
(YEL/BLK)
LG
(BRN/YEL)
CMP SENSOR B 3P CONNECTOR
CMP Sensor B No Signal
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
CMP sensor B and the ECM/PCM.
5. Turn the ignition switch OFF.
6. Disconnect the CMP sensor B 3P connector.
7. Turn the ignition switch ON (II).
8. Measure voltage between CMP sensor B 3P
connector terminal No. 3 and body ground.
Go to step 9.
Repair open in the wire between CMP sensor
B and PGM-FI main relay 1 (FI MAIN), then go to
step 18.
9. Measure voltage between CMP sensor B 3P
connector terminal No. 1 and body ground.
Go to step 10.
Go to step 11.
10. Measure voltage between CMP sensor B 3P
connector terminals No. 2 and No. 3.
Go to step 16.
Repair open in the wire between CMP sensor
B and G101, then go to step 18.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P0365 indicated?
Is ther e batter y voltage?
Is ther e about 5 V ?
Is ther e batter y voltage?
05/06/27 17:35:47 61S6M040_110_0189
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст