Acura RSX Honda Integra. Manual — part 119
01
02
S6M6AAJK72100090335FAAT10
−
−
−
−
−
−
DTC P0335:
DTC P0336:
DTC P0339:
YES
NO
YES
NO
YES
NO
11-182
PGM-FI System
DTC Troubleshooting (cont’d)
CKP SENSOR 3P CONNECTOR
IGP
(YEL/BLK)
CKP SENSOR 3P CONNECTOR
CKP
(BLU)
CKP Sensor No Signal
(2002-2004 models)
CKP Sensor Circuit Intermittent
Interruption
(2002-2003 models)
CKP Sensor Circuit Intermittent
Interruption
(2004 model)
NOTE:
• Information marked with an asterisk ( ) applies to
2002-2004 models.
• Information marked with double asterisk (
) applies
to 2002-2003 models.
• Information marked with triple asterisk (
) applies
to 2004 model.
1. Reset the ECM/PCM (see page 11-4).
2. Start the engine.
Go to step 3.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the CKP sensor and the ECM/PCM.
3. Turn the ignition switch OFF.
4. Disconnect the CKP sensor 3P connector.
5. Turn the ignition switch ON (II).
6. Measure voltage between CKP sensor 3P connector
terminal No. 3 and body ground.
Go to step 7.
Repair open in the wire between PGM-FI main
relay 1 and the CKP sensor.
7. Measure voltage between CKP sensor 3P connector
terminal No. 1 and body ground.
Go to step 8.
Go to step 10.
Wire side of female terminals
Wire side of female terminals
Is DT C P0335 and/ or ( P0336)
( P0339)
indicated?
Is ther e batter y voltage?
Is ther e about 5 V ?
05/06/27 17:35:45 61S6M040_110_0182
03
01
02
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-183
CKP SENSOR 3P CONNECTOR
LG1
(BRN/YEL)
IGP
(YEL/BLK)
ECM/PCM CONNECTOR A (31P)
CKP (BLU)
ECM/PCM CONNECTOR A (31P)
CKP (BLU)
8. Measure voltage between CKP sensor 3P connector
terminals No. 2 and No. 3.
Go to step 9.
Repair open in the wire between the CKP
sensor and G101.
9. Substitute a known-good CKP sensor and recheck.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Replace the original CKP sensor (see page
11-280).
10. Measure voltage between ECM/PCM connector
terminal A7 and body ground.
Repair open in the wire between the ECM/
PCM (A7) and the CKP sensor.
Go to step 11.
11. Turn the ignition switch OFF.
12. Disconnect ECM/PCM connector A (31P).
13. Check for continuity between ECM/PCM connector
terminal A7 and body ground.
Repair short in the wire between the ECM/
PCM (A7) and the CKP sensor.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is DT C P0335 and/ or ( P0336)
( P0339)
indicated?
Is ther e about 5 V ?
Is ther e continuity?
05/06/27 17:35:46 61S6M040_110_0183
01
02
03
S6M6AALK72100090335FAAT10
−
−
−
−
−
−
−
−
DTC P0335:
YES
NO
YES
NO
YES
NO
YES
NO
11-184
PGM-FI System
DTC Troubleshooting (cont’d)
CKP SENSOR 3P CONNECTOR
IGP
(YEL/BLK)
CKP SENSOR 3P CONNECTOR
CKP (BLU)
CKP SENSOR 3P CONNECTOR
LG
(BRN/YEL)
IGP
(YEL/BLK)
CKP Sensor No Signal
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the CKP sensor and the ECM/PCM.
5. Turn the ignition switch OFF.
6. Disconnect the CKP sensor 3P connector.
7. Turn the ignition switch ON (II).
8. Measure voltage between CKP sensor 3P connector
terminal No. 3 and body ground.
Go to step 9.
Repair open in the wire between the CKP
sensor and PGM-FI main relay 1 (FI MAIN), then go
to step 18.
9. Measure voltage between CKP sensor 3P connector
terminal No. 1 and body ground.
Go to step 10.
Go to step 11.
10. Measure voltage between CKP sensor 3P connector
terminals No. 2 and No. 3.
Go to step 16.
Repair open in the wire between the CKP
sensor and G101, then go to step 18.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P0335 indicated?
Is ther e batter y voltage?
Is ther e about 5 V ?
Is ther e batter y voltage?
05/06/27 17:35:46 61S6M040_110_0184
04
05
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
YES
NO
11-185
CKP (BLU)
ECM/PCM CONNECTOR A (31P)
CKP (BLU)
ECM/PCM CONNECTOR A (31P)
11. Measure voltage between ECM/PCM connector
terminal A7 and body ground.
Repair open in the wire between the ECM/
PCM (A7) and the CKP sensor, then go to step 18.
Go to step 12.
12. Turn the ignition switch OFF.
13. Jump the SCS line with the HDS.
14. Disconnect ECM/PCM connector A (31P).
15. Check for continuity between ECM/PCM connector
terminal A7 and body ground.
Repair short in the wire between the ECM/
PCM (A7) and the CKP sensor, then go to step 18.
Go to step 25.
16. Turn the ignition switch OFF.
17. Replace the CKP sensor (see page 11-280), then go
to step 18.
18. Reconnect all connectors.
19. Turn the ignition switch ON (II).
20. Reset the ECM/PCM with the HDS.
21. Clear the CKP pattern with the HDS.
22. Do the ECM/PCM idle learn procedure (see page
11-349).
23. Do the CKP pattern learn procedure (see page 11-5).
24. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0335 is indicated, check for poor
connections or loose terminals at the CKP sensor
and the ECM/PCM, then go to step 1. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Troubleshooting is complete.
25. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
26. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0335 is indicated, check for poor
connections or loose terminals at the CKP sensor
and the ECM/PCM, then go to step 1. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Wire side of female terminals
Wire side of female terminals
Is ther e about 5 V ?
Is ther e continuity?
Ar e any T empor ar y DT Cs or DT Cs indicated?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:35:46 61S6M040_110_0185
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст