Acura RSX Honda Integra. Manual — part 118
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-178
PGM-FI System
DTC Troubleshooting (cont’d)
63. Reconnect all connectors.
64. Turn the ignition switch ON (II).
65. Reset the ECM/PCM with the HDS.
66. Clear the CKP pattern with the HDS.
67. Do the ECM/PCM idle learn procedure (see page
11-349).
68. Do the CKP pattern learn procedure (see page 11-5).
69. Test-drive the vehicle for several minutes in the
range of these recorded freeze data parameters:
• Engine speed
• Vehicle speed
• Throttle position
• CLV (calculated load value)
• Gear position
70. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0301,P0302, P0303, or P0304 are
indicated, check for poor connections or loose
terminals at the ignition coil, the injector, and the
ECM/PCM, then go to troubleshooting DTC P0300,
P0301, P0302, P0303, or P0304 (see page 11-164). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s toubleshooting.
Go to step 71.
71. Monitor the OBD STATUS for DTC P0301, P0302,
P0303, or P0304 in the DTCs MENU with the HDS.
Troubleshooting is complete.
If the screen indicates FAILED, go to step 1
and recheck. If the screen indicates EXECUTING,
keep driving until a result comes on. If the screen
indicates OUT OF CONDITION, go to step 69 and
recheck.
72. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
73. Test-drive the vehicle for several minutes in the
range of the recorded freeze data.
74. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0301, P0302, P0303, or P0304 are
indicated, check for poor connections or loose
terminals at the injector, the ignition coil, and the
ECM/PCM, then go to step 1. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Ar e any T empor ar y DT Cs or DT Cs indicated?
Does the scr een indicate PASSED?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:35:06 61S6M040_110_0178
−
01
01
03
S6M6AAJK72100090325FAAT00
−
−
−
−
−
−
−
−
DTC P0325:
YES
NO
YES
NO
YES
NO
YES
NO
11-179
ECM/PCM CONNECTOR A (31P)
KS (RED/BLU)
ENGINE WIRE HARNESS
6P CONNECTOR*
ENGINE WIRE HARNESS
8P CONNECTOR*
KS
(RED/BLU)
KS
(RED/BLU)
JUMPER
WIRE
JUMPER
WIRE
ECM/PCM CONNECTOR A (31P)
KS (RED/BLU)
2
1
Knock Sensor Circuit Malfunction
(2002-2004 models)
NOTE: Information marked with
1 applies to K20A3
engine;
2 applies to K20A2 engine.
1. Reset the ECM/PCM (see page 11-4).
2. Start the engine. Hold the engine speed at
3,000 rpm without load (in Park or neutral) until the
radiator fan comes on, then let it idle.
3. Hold the engine speed at 3,000
4,000 rpm for at
least 10 seconds.
Go to step 4.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the knock sensor and the ECM/PCM.
4. Turn the ignition switch OFF.
5. Disconnect the starter subharness 8P
(6P)
connector.
6. Check for continuity between ECM/PCM connector
terminal A9 and body ground.
Repair short in the wire between the ECM/
PCM (A9) and the starter subharness 8P
(6P)
connector.
Go to step 7.
7. Connect engine wire harness 8P
(6P)
connector
terminal No. 7
(No. 5)
to body ground with a
jumper wire.
8. Check for continuity between body ground and
ECM/PCM connector terminal A9.
Go to step 9.
Repair open in the wire between the ECM/
PCM (A9) and the starter subharness 8P
(6P)
connector.
9. Check the starter subharness between 8P
(6P)
connector and the knock sensor for an open or
short. If it’s OK, substitute a known-good knock
sensor and recheck.
Update the ECM/PCM if it does not have the
latest software, or substitute a known-good ECM/
PCM (see page 11-6), then recheck. If the symptom/
indication goes away with a known-good ECM/PCM,
replace the original ECM/PCM (see page 11-284).
Replace the original knock sensor and/or
starter subharness, K20A2 engine (see page
11-282), K20A3 engine (see page 11-282).
1
2
1
2
1
2
1
2
1
2
1
2
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P0325 indicated?
Is ther e continuity?
Is ther e continuity?
Is DT C P0325 indicated?
05/06/27 17:35:06 61S6M040_110_0179
−
01
02
03
S6M6AALK72100090325FAAT00
−
−
−
−
−
−
DTC P0325:
YES
NO
YES
NO
YES
NO
11-180
PGM-FI System
DTC Troubleshooting (cont’d)
KS
(RED/BLU)
ECM/PCM CONNECTOR A (31P)
KNOCK SENSOR 1P CONNECTOR
KS (RED/BLU)
JUMPER WIRE
KS
(RED/BLU)
ECM/PCM CONNECTOR A (31P)
Knock Sensor Circuit Malfunction
(2005-2006 models)
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at
3,000 rpm without load (in Park or neutral) until the
radiator fan comes on, then let it idle.
4. Hold the engine speed at 3,000
4,000 rpm for at
least 10 seconds.
5. Check for Temporary DTCs or DTCs with the HDS.
Go to step 6.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the knock sensor and the ECM/PCM.
6. Turn the ignition switch OFF.
7. Jump the SCS line with the HDS.
8. Disconnect the knock sensor 1P connector.
9. Disconnect ECM/PCM connector A (31P).
10. Check for continuity between ECM/PCM connector
terminal A1 and body ground.
Repair short in the wire between the ECM/
PCM (A1) and the knock sensor, then go to step 14.
Go to step 11.
11. Connect the knock sensor 1P connector terminal to
body ground with a jumper wire.
12. Check for continuity between ECM/PCM connector
terminal A1 and body ground.
Go to step 13.
Repair open in the wire between the ECM/
PCM (A1) and the knock sensor, then go to step 14.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P0325 indicated?
Is ther e continuity?
Is ther e continuity?
05/06/27 17:35:07 61S6M040_110_0180
−
−
−
−
−
−
−
−
YES
NO
YES
NO
YES
NO
11-181
13. Replace the knock sensor, K20Z1 engine (see page
11-282), K20A3 engine (see page 11-282).
14. Reconnect all connectors.
15. Turn the ignition switch ON (II).
16. Reset the ECM/PCM with the HDS.
17. Do the ECM/PCM idle learn procedure (see page
11-349).
18. Hold the engine speed at 3,000
4,000 rpm for at
least 10 seconds.
19. Check for Temporary DTCs or DTCs with the HDS.
Go to step 21.
Go to step 20.
20. Monitor the OBD STATUS for DTC P0325 in the
DTCs MENU with the HDS.
Troubleshooting is complete.
If the screen indicates FAILED, go to step 1
and recheck. If the screen indicates NOT
COMPLETED, go to step 17 and recheck.
21. Update the ECM/PCM if it does not have the latest
software, or substitute a known-good ECM/PCM
(see page 11-6).
22. Hold the engine speed at 3,000
4,000 rpm for at
least 10 seconds.
23. Check for Temporary DTCs or DTCs with the HDS.
If DTC P0325 is indicated, check for poor
connections or loose terminals at the knock sensor
and the ECM/PCM, then go to step 1. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-284).
Ar e any T empor ar y DT Cs or DT Cs indicated?
Does the scr een indicate PASSED?
Ar e any T empor ar y DT Cs or DT Cs indicated?
05/06/27 17:35:45 61S6M040_110_0181
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст