Acura RSX Honda Integra. Manual — part 333
01
S6M6A00F00000057101KDAT00
Removal
17-25
Steering Column Removal and Installation
D
A
A
C
B
E
8 x 1.25 mm
28 N·m (2.9 kgf·m,
21 lbf·ft)
8 x 1.25 mm
16 N·m (1.6 kgf·m,
12 lbf·ft)
SRS components are located in this area. Review the SRS component locations (see page 23-10) and precautions and
procedures (see page 23-11) before performing repairs or service.
1. Record the radio station presets, and disconnect the battery.
2. Remove the driver’s airbag assembly and the steering wheel (see page 17-22).
3. Remove the driver’s dashboard lower cover (see page 20-63), and the driver’s dashboard under cover (see page
20-63).
4. Remove the column covers (A).
5. Remove the combination switch assembly (B) from the steering column shaft by removing the screw (C) on the
top of the combination switch. Disconnect the 5P, 14P, and 16P connectors from the switch.
6. Disconnect the 6P and two 7P connectors from the ignition switch. Disconnect the harness clips from the steering
column.
7. Disconnect the steering joint (D), and remove it from the column shaft.
8. Remove the steering column (E) by removing the attaching nuts and bolts.
(cont’d)
05/06/27 18:15:09 61S6M040_170_0026
02
Installation
17-26
Power Steering
Steering Column Removal and Installation (cont’d)
A
C
B
E
F
8 x 1.25 mm
28 N·m (2.9 kgf·m,
21 lbf·ft)
8 x 1.25 mm
28 N·m (2.9 kgf·m,
21 lbf·ft)
D
1. Install the steering column in the reverse order of
removal, and note these items:
• Take care not to let the sliding capsules fall out of
the position during column installation.
• Make sure the wires are not caught or pinched by
any parts.
2. Insert the upper end of the steering joint onto the
steering shaft (A) (line up the bolt hole (B) with the
flat portion (C) on the shaft).
3. Slip the lower end of the steering joint onto the
pinion shaft (D) (line up the bolt hole (E) with the
groove (F) around the shaft), and loosely install the
lower joint bolt. Be sure that the lower joint bolt is
securely in the groove in the pinion shaft.
4. Pull on the steering joint to make sure that the
steering joint is fully seated. Then install the upper
joint bolt and tighten both bolts to the specified
torque .
5. Install the driver’s dashboard lower cover
(see page 20-63).
6. Install the driver’s dashboard under cover
(see page 20-63).
7. Finish the installation, and note these items:
• Make sure the wire harness is routed and
fastened properly.
• Make sure the connectors are properly connected.
• Reinstall the steering wheel (see page 17-24).
• Reconnect the battery.
• 2002-2004 models: Do the ECM/PCM idle learn
procedure (see page 11-349).
• Do the power window control unit reset
procedure (see page 22-148).
• Enter the anti-theft code for the radio, then enter
the customer’s radio station presets.
• Set the clock.
• Verify horn and turn signal switch operation.
05/06/27 18:15:09 61S6M040_170_0027
*01
S6M6A00F00000057101MAAT30
Tilting load (upward/downward):
Standard: 68 N (7.0 kgf, 15 lbf) or below
17-27
Steering Column Tilt Operation Check
UPWARD
DOWNWARD
1. Set the steering wheel in the straight driving
position, and loosen the tilt lever fully.
2. Attach the spring scale to the highest point of the
steering wheel, and set the tilting position at the
lowest.
3. Pull the spring scale straight up, and read the
operation load during tilting.
4. Attach the spring scale to the lowest point of the
steering wheel.
5. Pull the spring scale straight down, and read the
operation load during tilting.
6. If the measurement is more than the specification,
adjust the tilt lever preload (see page 17-29).
05/06/27 18:15:09 61S6M040_170_0028
01
S6M6A00F00000057101MCAT00
17-28
Power Steering
Steering Column/Tilt Lever Inspection/Adjustment
A
C
C
B
• Check the steering column ball bearing (A) and the steering joint bearings (B) for play and proper movement. If any
bearing is noisy or has excessive play, replace the steering column as an assembly.
• Check the sliding capsules (C) for distortion and breakage. If there is distortion or breakage, replace the steering
column as an assembly.
05/06/27 18:15:09 61S6M040_170_0029
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст