Acura RSX Honda Integra. Manual — part 307
−
01
01
S6M6A02E10410917424KBAT00
−
−
Special Tools Required
14-353
Countershaft Bearing Replacement
07736-A01000B or
07736-A01000A
A
07749-0010000
07746-0010500
0
0.03 mm
(0
0.001 in.)
A
B
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Driver 07749-0010000
• Attachment, 62 x 68 mm 07746-0010500
1. Remove the countershaft bearing with the special
tool and a commercially available 3/8 ’’-16 slide
hammer (A).
2. Install the ATF guide plate (A).
3. Install the new countershaft bearing (B) in the
housing with the special tools.
05/06/27 17:59:01 61S6M040_140_0354
01
02
03
04
S6M6A02E10411354202KBAT00
Special Tools Required
14-354
Torque Converter Housing
Secondary Shaft Bearing Replacement
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
B
A
C
B
A
07749-0010000
07746-0010500
• Driver 07749-0010000
• Attachment, 62 x 68 mm 07746-0010500
1. Remove the bolt, then remove the lock washer (A)
and bearing set plate (B).
2. Remove the secondary shaft bearing (A) by heating
the housing to about 212 °F (100 °C) with a heat gun
(B). Do not heat the housing in excess of 212 °F
(100 °C).
NOTE: Let the housing cool to normal temperature
before installing the bearing.
3. Install the new O-rings (A) on the ATF guide collar
(B), then install the ATF guide collar in the housing.
4. Install the new secondary shaft bearing (C) in the
direction shown.
5. Drive the secondary shaft bearing with the special
tools, and install it securely in the housing.
6. Check that the bearing groove aligns with the
housing surface, then install the bearing set plate
with aligning the bearing groove.
7. Install the new lock washer and bolt, then bend the
lock tab of the lock washer against the bolt head.
05/06/27 17:59:02 61S6M040_140_0355
−
−
01
01
S6M6A02E10410417258KBAT00
Special Tools Required
14-355
Selector Control Shaft Oil Seal Replacement
A
B
07749-0010000
07947-ZV00100
A
B
• Driver 07749-0010000
• Oil seal driver attachment 07947-ZV00100
1. Remove the oil seal (A) from the torque converter
housing (B).
2. Install the new oil seal (A) in the torque converter
housing in depth (B) of 0.5
1.5 mm (0,02
0.06 in.)
below the housing surface with the special tools.
05/06/27 17:59:02 61S6M040_140_0356
01
S6M6A02E10411200000MEAT00
→ →
14-356
Shafts and Clutches
Mainshaft Disassembly, Inspection, and Reassembly
LOCKNUT (FLANGE NUT)
24 x 1.25 mm
226 N·m (23.0 kgf·m, 166 lbf·ft)
0
167 N·m (17.0 kgf·m, 123 lbf·ft)
CONICAL SPRING
WASHER
IDLER GEAR
TRANSMISSION
HOUSING BEARING
THRUST NEEDLE BEARING
4TH GEAR
NEEDLE BEARING
THRUST NEEDLE BEARING
4TH GEAR COLLAR
4TH/5TH CLUTCH
O-RING
THRUST WASHER, 41 x 68 mm
NEEDLE BEARING
THRUST NEEDLE BEARING
5TH GEAR
THRUST NEEDLE BEARING
SEALING RINGS,
29 mm
NEEDLE BEARING
SET RING
1. Inspect the thrust needle bearing and the needle bearing for galling and rough movement.
2. Inspect the splines for excessive wear and damage.
3. Check shaft bearing surface for scoring and excessive wear.
4. Before installing the O-rings, wrap the shaft splines with tape to prevent O-ring damage.
5. Lubricate all parts with ATF during assembly.
6. Install the conical spring washer, 41 x 68 mm thrust washer in the direction shown.
7. Replace the locknut and conical spring washer with new ones when assembling the transmission.
8. Check the clearance of the 5th gear (see page 14-357).
Repalce.
Replace.
Replace.
Selective part
05/06/27 17:59:02 61S6M040_140_0357
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст