Acura RSX Honda Integra. Manual — part 306
*01
S6M6A02E10480150701MEAT00
SPRING SPECIFICATIONS
Spring
Standard (New)-Unit: mm (in.)
Wire Diameter
O.D.
Free Length
No. of Coils
14-349
Regulator Valve Body Disassembly, Inspection, and Reassembly
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
F
G
H
1ST ACCUMULATOR
PISTON
O-RING
REGULATOR VALVE BODY
LOCK-UP SHIFT VALVE
E
VALVE CAP CLIP
VALVE CAP
REGULATOR VALVE
TORQUE CONVERTER
CHECK VALVE
D
SPRING SEAT
A
B
C
ACCUMULATOR COVER
3RD ACCUMULATOR
PISTON
REGULATOR
SPRING CAP
STOP BOLT
6 x 1.0 mm
12 N·m (1.2 kgf·m,
8.7 lbf·ft)
1. Clean all parts thoroughly in solvent or carburetor cleaner, and dry them with compressed air. Blow out all
passages.
2. Check all valves for free movement. If any fail to slide freely, refer to valve body repair (see page 14-345).
3. Hold the regulator spring cap in place while removing the stop bolt. The regulator spring cap is spring loaded.
Once the stop bolt is removed, release the spring cap slowly so it does not pop out.
4. Coat all parts with ATF during assembly.
5. When reassembling the valve body, align the hole in the regulator spring cap with the hole in the valve body, then
press the spring cap into the valve body, and tighten the stop bolt.
A
Stator reaction spring
4.5 (0.177)
35.4 (1.394)
30.3 (1.193)
1.92
B
Regulator valve spring A
1.9 (0.075)
14.7 (0.579)
80.6 (3.173)
16.1
C
Regulator valve spring B
1.6 (0.063)
9.2 (0.362)
44.0 (1.732)
12.5
D
Torque converter check valve spring
1.2 (0.047)
8.6 (0.339)
33.8 (1.331)
12.2
E
Lock-up shift valve spring
1.0 (0.039)
6.6 (0.260)
35.5 (1.398)
18.2
F
3rd accumulator spring
2.5 (0.098)
14.6 (0.575)
29.9 (1.177)
4.9
G
1st accumulator spring A
2.4 (0.094)
18.6 (0.732)
49.0 (1.929)
7.1
H
1st accumulator spring B
2.3 (0.091)
12.2 (0.480)
31.5 (1.240)
6.6
Replace.
Inspect for scoring and damage.
05/06/27 17:59:00 61S6M040_140_0350
*01
S6M6A02E10480154501MEAT00
SPRING SPECIFICATIONS
Springs
Standard (New)-Unit: mm (in.)
Wire Diameter
O.D.
Free Length
No. of Coils
14-350
Valve Body
Servo Body Disassembly, Inspection, and Reassembly
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
ACCUMULATOR COVER
SHIFT SOLENOID VALVE A
SHIFT SOLENOID VALVE D
SHIFT SOLENOID VALVE B
SHIFT SOLENOID VALVE E
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
SHIFT SOLENOID VALVE C
O-RINGS
F
5TH ACCUMULATOR
PISTON
O-RING
SERVO BODY
O-RING
SERVO VALVE/
SHIFT FORK SHAFT
E
D
2ND ACCUMULATOR PISTON
C
B
4TH ACCUMULATOR PISTON
SHIFT
VALVE D
A
SPRING SEAT
O-RING
O-RING
1. Clean all parts thoroughly in solvent or carburetor cleaner, and dry them with compressed air. Blow out all
passages.
2. Inspect the valve body for scoring and damage.
3. Check shift valve D for free movement. If any fail to slide freely, refer to valve body repair (see page 14-345).
4. Do not hold the shift solenoid valve connector to remove and install it. Be sure to hold the shift solenoid valve
body. When installing the shift solenoid valves, refer to Shift Solenoid Valves Installation (see page 14-351).
5. Coat all parts with ATF during assembly.
6. Replace the O-rings with new ones.
A
Shift valve D spring
0.8 (0.031)
5.6 (0.220)
28.1 (1.106)
15.9
B
4th accumulator spring B
2.3 (0.091)
12.2 (0.480)
31.5 (1.240)
6.6
C
4th accumulator spring A
2.4 (0.094)
18.6 (0.732)
49.0 (1.929)
7.1
D
2nd accumulator spring B
2.0 (0.079)
10.6 (0.417)
34.0 (1.339)
8.0
E
2nd accumulator spring A
2.2 (0.087)
16.6 (0.654)
48.2 (1.898)
8.5
F
5th accumulator spring
2.5 (0.098)
14.6 (0.575)
29.9 (1.177)
4.9
Replace.
Replace.
Inspect for scoring
and damage.
Replace.
Replace.
Replace.
05/06/27 17:59:01 61S6M040_140_0351
01
S6M6A02E10410654801KCAT50
14-351
Shift Solenoid Valve Installation
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
D
E
F
B
F
C
F
A
NOTE:
• Do not install shift solenoid valve A and B before
installing shift solenoid valve D and E. If solenoid
valve A and B are installed before solenoid valves D
and E, it may damage the hydraulic control system.
• Do not hold the shift solenoid valve connector to
install it. Hold the shift solenoid valve body.
1. Install the new O-rings (F) on each shift solenoid
valves.
NOTE: The new shift solenoid valve is equipped
with new O-ring. If you install a new shift solenoid
valve, there is no need to replace its O-rings.
2. Install shift solenoid valve D by holding the shift
solenoid valve body; be sure to install the
mounting bracket contacts the servo body.
3. Install shift solenoid valve A by holding the shift
solenoid valve body; be sure to install the
mounting bracket contacts the bracket on shift
solenoid valve D.
4. Install shift solenoid valve E by holding the shift
solenoid valve body; be sure to install the
mounting bracket contacts the servo body.
5. Install shift solenoid valve B by holding the shift
solenoid valve body; be sure to install the
mounting bracket contacts the bracket on shift
solenoid valve E.
6. Install shift solenoid valve C by holding the shift
solenoid valve body; be sure to install the
mounting bracket contacts the servo body.
05/06/27 17:59:01 61S6M040_140_0352
−
01
01
02
S6M6A02E10411239521KBAT00
Special Tools Required
14-352
Torque Converter Housing
Mainshaft Bearing and Oil Seal Replacement
07736-A01000B or
07736-A01000A
A
07749-0010000
07746-0010500
07749-0010000
07746-0010600
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
• Driver 07749-0010000
• Attachment, 62 x 68 mm 07746-0010500
• Attachment, 72 x 75 mm 07746-0010600
1. Remove the mainshaft bearing and oil seal with the
special tool and a commercially available 3/8 ’’-16
slide hammer (A).
2. Install the new mainshaft bearing until it bottoms in
the torque converter housing with the special tools.
3. Install the new oil seal flush with the housing with
the special tools.
05/06/27 17:59:01 61S6M040_140_0353
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст