Acura RSX Honda Integra. Manual — part 449
*01
*02
S6M6A00J34300044051DAAT01
22-135
Power Mirrors
Component Location Index
POWER MIRRORS
POWER MIRROR and
MIRROR DEFOGGER SWITCH
Test, page 22-137
Power Mirror Actuator Test, page 22-138
Mirror Actuator Replacement, page 22-139
Test, page 22-138
Replacement, page 22-138
05/06/27 18:04:46 61S6M040_220_0136
*01
S6M6A00J34300000000EAAT00
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
22-136
Power Mirrors
Circuit Diagram
1
2
5
1
4
3
6
2
No. 20*
IG2 HOT in ON (II)
RED
LIGHT
(0.91 W)
RED/BLK
9
4
BLU/WHT
BLK/YEL
BLK/YEL
DOWN
ORN
ORN
ORN
G402
G401
BLK
2
1
DEFOGGER*
DEFOGGER*
BLK
GRN/WHT
BLU/BLK
RED/YEL
BLU/WHT
GRN/WHT
GRN/WHT
LEFT MIRROR
RIGHT MIRROR
2
5
3
6
1
4
UP
RIGHT
LEFT
DOWN
DOWN
LEFT
RIGHT
UP
WHT/RED
G401
POWER MIRROR SWITCH
5
2
BLK/YEL
RIGHT
LEFT
UP
6
13
12
11
10
RIGHT
LEFT
LEFT
RIGHT
No. 14 (10 A)
IGNITION SWITCH
IG2
BAT
UNDER-HOOD FUSE/RELAY BOX
BLK
WHT
No. 19 (100 A)
BATTERY
UNDER-DASH
FUSE/RELAY BOX
TAILLIGHT
RELAY
DEFOGGER
SWITCH*
INDICATOR
LIGHT*
(LED)
DASH LIGHTS
BRIGHTNESS
CONTROLLER
(In the gauge
assembly)
1*
8*
BLK/RED
No. 20 (40 A) : USA
No. 20 (50 A) : Canada
*2: With defogger
: ’02-04 Canada models and ’05-06 models
*1
1
2
2
2
2
2
2
05/06/27 18:04:47 61S6M040_220_0137
01
S6M6A00J34300044051FEAT00
Both mirrors
Left mirror
Right mirror
Defogger
22-137
Function Test
BLK/YEL
BLK/YEL*
RED
GRN/WHT
BLK
ORN*
RED/BLK
BLU/BLK
RED/YEL
BLU/WHT
WHT/RED
A
B
*: With defogger
1. Carefully pry out the driver’s switch panel
(see page 20-64).
2. Disconnect the 13P connector (A) from the power
mirror switch (B).
3. Remove the two screws and the power mirror
switch.
4. Choose the appropriate test based on the
symptom:
• Both mirrors don’t work, go to step 5.
• Left mirror doesn’t work, go to step 7.
• Right mirror doesn’t work, go to step 8.
• Defogger doesn’t work, go to step 9.
5. Check for voltage between the No. 2 terminal and
body ground with the ignition switch ON (II).
There should be battery voltage.
• If there is no battery voltage, check for:
– Blown No. 14 (10 A) fuse in the under-dash
fuse/relay box.
– An open in the BLK/YEL wire.
• If there is battery voltage, go to step 6.
6. Check for continuity between the No. 6 terminal
and body ground.
There should be continuity.
• If there is no continuity, check for:
– An open in the BLK wire.
– Poor ground (G 401).
• If there is continuity, check both mirrors
individually as described in the next column.
7. Connect the No. 2 terminal to the No. 10 terminal,
and the No. 5 (or No. 12) terminal to body ground
with jumper wires. The left mirror should tilt down
(or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the GRN/WHT (or BLU/
WHT) wire between the left mirror and the 13P
connector. If the wire is OK, check the left mirror
actuator.
• If the mirror neither tilts down nor swings left,
repair the BLU/BLK wire.
• If the mirror works properly, check the mirror
switch (see page 22-138).
8. Connect the No. 2 terminal to the No. 11 terminal,
and the No. 5 (or No. 13) terminal to body ground
with jumper wires. The right mirror should tilt
down (or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the GRN/WHT (or WHT/
RED) wire between the right mirror and the 13P
connector.
If the wire is OK, check the right mirror actuator.
• If the mirror neither tilts down nor swings left,
repair the RED/YEL wire.
• If the mirror works properly, check the mirror
switch (see page 22-138).
9. Connect the No. 1 and No. 8 terminals with a
jumper wire, and check for voltage between the
No. 1 terminal of the mirror connector and body
ground. There should be battery voltage and both
mirrors should warm up with the ignition switch
ON (II).
• If there is no voltage or neither warms up, check
for:
– An open in the BLK/YEL, BLK, or ORN wire.
– Blown No. 14 (10 A) fuse in the under-dash
fuse/relay box.
– Poor ground (G 401, G402).
• If only one fails to warm up, check its defogger.
• If both warm up, check the defogger switch.
Wire side of
female terminals
05/06/27 18:04:47 61S6M040_220_0138
01
01
02
S6M6A00J34300044041FHAT10
01
*02
S6M6A00J34300044031FEAT00
[ ]
[ ]
[ ]
[ ]
Mirror Switch:
Defogger Switch:
Defogger Test
22-138
22-138
Power Mirrors
Power Mirror Switch Test/
Replacement
Power Mirror Actuator Test
A
B
A
B
*1
*2
Terminal
Position
UP
DOWN
LEFT
RIGHT
L
UP
DOWN
LEFT
RIGHT
R
2
5
6
10
11
12
13
Terminal
Position
ON
OFF
1
8
Terminal
Position
1
4
2
5
3
6
TILT UP
TILT DOWN
SWING LEFT
SWING RIGHT
: ’02-04 Canada models and ’05-06 models
1. Carefully pry out the driver’s switch panel
(see page 20-64).
2. Disconnect the 13P connector (A) from the power
mirror switch (B).
3. Remove the two screws and the switch.
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified, replace the
switch.
1. Remove the door panel (see page 20-5).
2. Disconnect the 3P
or 6P
connector (A) from the
power mirror actuator (B).
1:
’02-04 USA models
2:
’02-04 Canada models and ’05-06 models
3. Check actuator operation by connecting power and
ground according to the table.
4. If the mirror fails to work properly, replace the
mirror actuator.
5. Check for continuity between the No. 1 and No. 2
terminals of the 6P connector. There should be
continuity.
6. If the continuity is not as specified, replace the
mirror actuator.
1
2
Wire side of female terminals
05/06/27 18:04:47 61S6M040_220_0139
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст