Acura RSX Honda Integra. Manual — part 448
01
02
S6M6A22J34200041501FHAT00
01
02
S6M6A22J34200041001FEAT00
22-131
22-131
Switch Test/Replacement
Motor Test
B
C
A
B
A
Terminal
Position
CLOSE
OPEN
2
5
1
3
6
Terminal
Position
OPEN
CLOSE
1
2
1. Carefully pry out the driver’s switch panel
(see page 20-64).
2. Disconnect the 6P connector (A) from the moonroof
switch (B), then remove the switch.
3. Check for continuity between the terminals in each
switch position according to the table.
4. If the continuity is not as specified, replace the
illumination bulbs (C) or the switch.
1. Remove the headliner (see page 20-55).
2. Disconnect the 2P connector (A) from the moonroof
motor (B).
3. Check the motor by connecting power and ground
according to the table.
4. If the motor does not run, replace it.
NOTE: See closing force check (see page 20-48) for
motor clutch test.
05/06/27 18:04:43 61S6M040_220_0132
*01
S6M6A00J24200000000DAAT10
22-132
Horns
Component Location Index
UNDER-HOOD FUSE/RELAY BOX
HORN RELAY
HORN
CABLE REEL
HORN SWITCH
Test, page 22-62
Test, page 22-133
Replacement, page 22-133
Replacement, page 23-138
Test, page 22-134
05/06/27 18:04:44 61S6M040_220_0133
*01
S6M6A00J24200000000EAAT10
01
02
S6M6A00J24200032431FHAT20
22-133
22-133
Circuit Diagram
Horn Test/Replacement
BATTERY
UNDER-HOOD
FUSE/RELAY BOX
WHT/GRN
No. 7
(15 A)
ORN
BLU/RED
CABLE
REEL
HORN
HORN
SWITCH
: Grounds through steering column.
BRAKE LIGHTS
*
*
HORN
RELAY
A
B
B
A
1. Remove the front bumper.
• ’02-04 models (see page 20-90)
• ’05-06 models (see page 20-91)
2. Disconnect the 1P connector (A), and remove the
horn (B).
3. Test the horn by connecting battery power to the
terminal (A) and ground to the bracket (B). The horn
should sound.
4. If it fails to sound, replace it.
5. Install the horn in the reverse order of removal.
05/06/27 18:04:45 61S6M040_220_0134
*01
01
S6M6A00J24200032411FEAT10
22-134
Horns
Horn Switch Test
A
B
A
B
1. Remove the steering column covers (see page
17-25).
2. Disconnect the dashboard wire harness 5P
connector (A) from the cable reel (B).
3. Using a jumper wire, connect the dashboard wire
harness 5P connector No. 2 terminal to body
ground.
• If the horn sounds, go to step 4.
• If the horn does not sound, check these items:
– Horn relay
– No. 7 (15 A) fuse in the under-hood fuse/relay
box
– Horn (see page 22-133)
– An open in the wire
4. Check for continuity between the cable reel No. 2
terminal and body ground with the horn switch
pushed. There should be continuity. If there is no
continuity, go to step 5.
5. Reconnect the dashboard wire harness 5P
connector (A), and disconnect the horn switch
positive 1P connector (B).
6. Using a jumper wire, connect the horn switch
positive 1P connector to ground.
• If the horn sounds, go to step 7.
• If the horn does not sound, replace the cable reel.
7. Reconnect the horn switch positive 1P connector,
using a jumper wire, connect the steering wheel to
body ground.
8. Close the contact between the horn plate and the
contact place.
• If the horn sounds, replace the steering column.
• If the horn does not sound, replace the horn and
contact plate.
05/06/27 18:04:45 61S6M040_220_0135
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст