Acura RSX Honda Integra. Manual — part 391
02
01
S6M6A00J18533530955KBAT00
20-101
20-101
Hatch Support Strut Replacement
C
A
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
5. Tighten each screw and nut securely.
6. Check that the hatch opens properly and locks
securely.
7. Reinstall the support struts securely.
8. Reinstall all remaining removed parts.
9. Apply multipurpose grease to the pivot portion of
the hatch hinges as indicated by the arrows.
NOTE:
• Have an assistant help you when removing and
installing the support strut.
• Take care not to scratch the body and hatch.
1. Remove the pivot bolt (A) from the body.
2. Remove the pivot bolt (B) from the hatch, then
remove the support strut (C).
3. Install the support strut in the reverse order of
removal.
05/06/27 18:24:54 61S6M040_200_0102
01
S6M6A00J18533530965KBAT00
20-102
Hatch
Hatch Weatherstrip Replacement
A
A
B
Forward
1. Remove the hatch weatherstrip (A) by pulling out
on it.
2. Locate the painted alignment mark (B) on the hatch
weatherstrip. Align the painted mark with the
alignment tab in the center of the hatch opening,
and install the hatch weatherstrip all the way
around in the direction shown. Make sure there are
no wrinkles in the weatherstrip.
3. Check for water leaks.
05/06/27 18:24:54 61S6M040_200_0103
01
02
S6M6A00J18526300000MBAT00
20-103
Fuel Fill Door
Adjustment
B
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
1. Slightly loosen the hinge mounting bolts (A).
2. Adjust the fuel fill door (B) in or out until it’s flush
with the body, and up or down as necessary to
equalize the gaps.
3. Tighten the hinge mounting bolts.
4. Check that the fuel fill door opens properly and
locks securely, and check that the rear of the door is
flush with the body.
5. Apply multipurpose grease to each location
indicated by the arrows.
6. Apply touch-up paint to the hinge mounting bolts
and around the hinges.
05/06/27 18:24:55 61S6M040_200_0104
01
S6M6AZFJ18573430211KBAT00
01
S6M6AZHJ18573430211KBAT00
’02-04 Models
’05-06 Models
20-104
20-104
Exterior Trim
Front Grille Cover Replacement
Fastener Locations
: Screw, 4
C
D
A
E
B
E
D
Fastener Locations
: Clip, 2
C
D
A
B
A
A
B
D
1. Remove the front bumper (see page 20-90).
2. Remove the front grille cover (A) and front emblem
base (B). Take care not to scratch the front bumper
(C).
–1 Remove the screws and push nuts (D).
–2 Remove the front emblem base from the front
bumper.
–3 Pull the front grille cover away to release the
pins (E) of the front bumper.
3. Install the grille cover and emblem base in the
reverse order of removal, and note these items:
• Replace the push nuts with new ones.
• Push the push nuts into place securely.
4. Reinstall the front bumper.
1. Remove the front bumper (see page 20-91).
2. Remove the clips. Release the hooks (A) of the front
grille cover (B), and pull the cover away to release
the it’s groove (C) from the front bumper (D), then
remove the cover.
3. Install the grille cover in the reverse order of
removal, and note these items:
• Push the hooks into place securely.
• Replace any damaged or stress-whitenings clips.
4. Reinstall the front bumper.
05/06/27 18:24:55 61S6M040_200_0105
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст