Acura RSX Honda Integra. Manual — part 390

＊０１

Ｓ６Ｍ６Ａ００Ｊ１８５３３２０００００ＭＢＡＴ００

20-97

Hood

Adjustment

6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)

6 x 1.0 mm
18 N·m
(1.8 kgf·m,
13 lbf·ft)

A

D

E

D

C

B

1. Slightly loosen each hood hinge bolt.

2. Adjust the hood (A) alignment in this sequence:

• Adjust the hood right and left, as well as forward and rearward, by using the elongated holes on the hood hinge

(B).

• Turn the hood edge cushions (C), as necessary, to make the hood fits flush with the body at the front and side

edges.

3. Adjust the hood latch (D) to obtain the proper height at the forward edge, and move the hood latch right or left

until the striker (E) is centered in the hood latch.

4. Tighten each bolt securely.

(cont’d)

05/06/27 18:24:31 61S6M040_200_0098

０２

０３

０１

Ｓ６Ｍ６Ａ００Ｊ１８５３３２３２２０１ＫＢＡＴ１０

20-98

20-98

Hood

Adjustment (cont’d)

Hood Seal Replacement

A

: Clip, 6

B

Fastener Locations

: Clip, 12

A

D

C

B

C

A

5. Check that the hood opens properly and locks

securely.

6. Apply touch-up paint to the hinge mounting bolts

and around the hinges.

7. Apply multipurpose grease to each location of the

hood latch and hood hinge as indicated by the
arrows.

1. Using a clip remover, detach the clips (A, B), then

remove the hood seals (C) and center hood seal (D).
Take care not to scratch the hood.

2. Install the seals in the reverse order of removal,

and note these items:

• Replace any damaged or stress-whitened clips.
• Push the clips into place securely.

05/06/27 18:24:31 61S6M040_200_0099

０１

０１

Ｓ６Ｍ６Ａ００Ｊ１８５３３２３１７０１ＫＢＡＴ００

For Some Models

20-99

Hood Insulator Replacement

B

Fastener Location

: Clip, 1

C

C

B

A

A

C

A

A

A

A

A

A

A

A

A

B

D

B

Fastener Locations

:Clip, 9

:Clip, 1

1. Disconnect the windshield washer tubes (A), and

release the tube from the clip (B) and the hooks (C).

2. Using a clip remover, detach the clips (A, B).

Release the hooks (C), then remove the hood
insulator (D). Take care not to scratch the hood.

3. Install the insulator in the reverse order of removal,

and note these items:

• Replace any damaged or stress-whitened clips.
• Push the clips into place securely.
• Make sure the windshield washer tubes are

connected properly.

05/06/27 18:24:32 61S6M040_200_0100

０１

Ｓ６Ｍ６Ａ００Ｊ１８５３３５０００００ＭＢＡＴ００

20-100

Hatch

Adjustment

8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)

B

C

A

D

D

8 x 1.25 mm
18 N·m
(1.8 kgf·m, 13 lbf·ft)

Rear

1. Remove the support strut from each side (see page 20-101).

2. Remove the headliner (see page 20-55).

3. Slightly loosen each screw and nut.

4. Adjust the hatch (A) alignment in the following sequence:

• Adjust the hatch hinges (B) right and left, as well as forward and rearward, using the elongated holes.
• Turn the hatch edge cushions (C) in or out, as necessary, to make the hatch fit flush with the body at the side

edges.

• Adjust the fit between the hatch and hatch opening by moving the striker (D).

05/06/27 18:24:54 61S6M040_200_0101