Acura RSX Honda Integra. Manual — part 285
*01
S6M6A02E10410612223KBAT30
14-265
A/T Clutch Pressure Control Solenoid Valve B and C Replacement
F
D
E
A
A
B, C
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
1. Remove the air cleaner housing.
2. Disconnect the A/T clutch pressure control solenoid
valves B and C connectors.
3. Remove the mounting bolts, harness clamp
brackets (A), and the A/T clutch pressure control
solenoid valves B and C.
4. Remove the ATF joint pipes (D), O-rings (E), and
gasket (F).
5. Clean the mounting surface and fluid passages of
the A/T clutch pressure control solenoid valves B
and C, and transmission housing.
6. Clean the filter of the ATF joint pipes.
7. Install the new gasket on the transmission housing,
and install the ATF joint pipes.
8. Install the new O-rings over the ATF joint pipes.
9. Install the new A/T clutch pressure control solenoid
valves B and C, and harness clamp brackets.
10. Check the A/T clutch pressure control solenoid
valves B and C connectors for rust, dirt, or oil, and
clean if necessary, then connect them securely.
11. Install the air cleaner housing.
05/06/27 17:57:18 61S6M040_140_0266
01
S6M6A02E10410634615KBAT00
14-266
Automatic Transmission
Input Shaft (Mainshaft) and Output Shaft (Countershaft) Speed Sensor
Replacement
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
C
A
D
B
1. Disconnect the input shaft (mainshaft) speed
sensor connector and output shaft (countershaft)
speed sensor connector.
2. Remove the input shaft (mainshaft) speed sensor
(A) and output shaft (countershaft) speed sensor (B).
3. Install the new O-ring (C) on the input shaft
(mainshaft) speed sensor, and install the input
shaft (mainshaft) speed sensor in the transmission
housing.
4. Install the new O-ring (D) on the output shaft
(countershaft) speed sensor, and install the output
shaft (countershaft) speed sensor in the
transmission housing.
5. Check the connectors for rust, dirt, or oil, then
connect the connectors securely.
05/06/27 17:57:18 61S6M040_140_0267
01
S6M6A02E10410610101KBAT00
01
S6M6A02E10410610111KBAT00
14-267
14-267
2nd Clutch Transmission Fluid
Pressure Switch Replacement
3rd Clutch Transmission Fluid
Pressure Switch Replacement
A
20 N·m
(2.0 kgf·m, 14 lbf·ft)
B
A
20 N·m
(2.0 kgf·m, 14 lbf·ft)
B
1. Remove the air cleaner housing.
2. Disconnect the connector from the 2nd clutch
transmission fluid pressure switch (A).
3. Remove the 2nd clutch transmission fluid pressure
switch, then install a new one with a new sealing
washer (B). Tighten the switch to the specified
torque.
4. Reconnect the connector, making sure there is no
water, oil, dust, or foreign particles inside the
connector.
5. Install the air cleaner housing.
1. Disconnect the connector from the 3rd clutch
transmission fluid pressure switch (A).
2. Remove the 3rd clutch transmission fluid pressure
switch, then install a new one with a new sealing
washer (B). Tighten the switch to the specified
torque.
3. Reconnect the connector, making sure there is no
water, oil, dust, or foreign particles inside the
connector.
05/06/27 17:57:18 61S6M040_140_0268
01
02
S6M6A02E10410613041FHAT00
14-268
Automatic Transmission
ATF Temperature Sensor Test/Replacement
B
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m, 36 lbf·ft)
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
D
C
F
E
28 N·m
(2.9 kgf·m, 21 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
H
G
1. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF).
2. Reinstall the drain plug with a new sealing washer
(B).
3. Place the transmission jack under the transmission,
and lift it up to create clearance between the
transmission and front subframe.
4. Disconnect the shift solenoid harness connector.
5. Remove the bolt (A) securing the bracket (B) of the
ATF cooler inlet line (C) on the shift solenoid valve
cover (D), and remove the line bolt (E) with sealing
washers (F).
6. Remove the shift solenoid valve cover, gasket (G),
and dowel pins (H).
05/06/27 17:57:19 61S6M040_140_0269
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст