Acura RSX Honda Integra. Manual — part 395
01
S6M6A00J18526327912KBAT00
20-117
Fuel Fill Door Opener Cable Replacement
Fastener Locations
C
: Clip, 2
D
: Cushion
tape, 2
E
E
C
C
D
D
A
B
SRS components are located in this area. Review the SRS component locations (see page 23-10) and the precautions
and procedures (see page 23-11) before performing repairs or service.
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the body and related parts.
1. Remove these items from the left side of the vehicle:
• Rear side trim panel (see page 20-51)
• Cargo area side trim panel (see page 20-53)
2. Pull the carpet back as necessary (see page 20-57).
3. Disconnect the fuel fill door opener cable (A) from the opener (B) (see step 4 on page 20-120).
4. Remove the opener cable from the clips (C). Remove the cushion tape (D).
5. Remove the fuel fill door latch (E) from the body by turning it 90 °.
6. Remove the opener cable from the vehicle. Take care not to kink the cable.
(cont’d)
05/06/27 18:25:02 61S6M040_200_0118
02
20-118
Openers
Fuel Fill Door Opener Cable Replacement (cont’d)
A
7. Install the opener cable in the reverse order of removal, and note these items:
• Replace the cushion tape and any damaged or stress-whitened clips.
• Align the mark (A) on the opener cable with the clip.
• Make sure the fuel fill door opens properly and locks securely.
05/06/27 18:25:02 61S6M040_200_0119
01
02
03
04
S6M6A00J18533231801KBAT00
20-119
Hood Latch Replacement
Fastener Locations
: Bolt, 3
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
C
A
B
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the body.
1. Remove the front bumper, ’02-04 models (see page
20-90), ’05-06 models (see page 20-91).
2. Remove the bolts, then remove the hood latch (A)
from the body.
3. Disconnect the hood opener cable (A) from the
hood latch. Take care not to kink the cable.
4. Detach the hood latch switch connector clip (A)
from the body, and disconnect the hood latch
switch connector (B), then remove the hood latch
(C).
5. Install the latch in the reverse order of removal, and
note these items:
• Apply multipurpose grease to each location of
the hood latch indicated by the arrows.
• Make sure the hood latch switch connector is
plugged in properly and the hood opener cable is
connected properly.
• Make sure the cable actuates the latch before you
close the hood.
• Adjust the hood latch alignment (see step 3 on
page 20-97).
• Make sure the hood opens properly and locks
securely.
05/06/27 18:25:03 61S6M040_200_0120
01
S6M6A00J18526327911KBAT00
20-120
Openers
Fuel Fill Door Opener Replacement
Fastener Locations
: Bolt, 2
A
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
NOTE: Put on gloves to protect your hands.
1. Slide the driver’s front seat rearward fully.
2. Remove these items from the left side of the
vehicle (see page 20-50):
• Door sill trim
• Kick panel
3. Pull the carpet back as necessary (see page 20-57).
4. Remove the bolts, then remove the fuel fill door
opener (A) from the body.
5. Disconnect the fuel fill door opener cable (B) from
the opener, then remove the opener. Take care not
to kink the cable.
6. Install the opener in the reverse order of removal,
and note these items:
• Make sure the opener cable is connected
properly.
• Make sure the fuel fill door opens properly and
locks securely.
05/06/27 18:25:12 61S6M040_200_0121
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст