Acura RSX Honda Integra. Manual — part 396
01
02
S6M6A00J18533530923KBAT00
Special Tools Required
20-121
Hatch Handle Replacement
Fastener Locations
: Nut, 2
D
C
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
A
A
B
KTC trim tool set SOJATP2014
NOTE:
• Put on gloves to protect your hands.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
1. Remove the hatch trim panel (see page 20-54).
2. Using a trim tool, gently pry out the hatch handle
cover (A) to detach the hook (B) from each side.
3. Remove the nuts, and pull the hatch handle (C) out
through the hole in the hatch. Take care not to kink
the hatch opener cable (D).
4. Disconnect the hatch opener cable (A) from the
hatch handle (B), then remove the handle.
5. Install the handle in the reverse order of removal,
and note these items:
• Make sure the hatch opener cable is connected
securely.
• Make sure the hatch opens properly.
05/06/27 18:25:13 61S6M040_200_0122
01
*01
S6M6A00J18533530928KBAT10
20-122
Openers
Hatch Latch Replacement
Fastener Locations
: Bolt, 3
A
C
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
NOTE: Put on gloves to protect your hands.
1. Remove the hatch trim panel (see page 20-54).
2. Disconnect the hatch lock actuator connectors (A)
and hatch latch switch connector (B), and detach
the hatch latch switch connector from the hatch.
3. While holding the hatch latch (C), remove the bolts,
then remove the latch from the hatch.
4. Disconnect the hatch opener cable (A) from the
latch and the bushing (B).
NOTE: Check the bushing for damage and replace if
necessary.
5. Install the latch in the reverse order of removal, and
note these items:
• Make sure each connector is plugged in properly,
and the cable is connected properly.
• Make sure the cable actuates the latch before you
close the hatch.
• Make sure the hatch opens properly and locks
securely.
05/06/27 18:25:13 61S6M040_200_0123
*01
S6M6A00J20170700000KBAT00
Subframe Torque
20-123
Frame
Subframe Replacement
8 x 1.25 mm
26 N·m
(2.7 kgf·m, 20 lbf·ft)
FRONT SUSPENSION
SUBFRAME
To body
FRONT DAMPER
(For some models)
SPECIAL BOLTS
14 x 1.5 mm
103 N·m
(10.5 kgf·m,
76 lbf·ft)
To body
To body
To body
INSTALLATION
REFERENCE HOLE
INSTALLATION
REFERENCE
HOLE
SCREWDRIVER or
TAPERED PUNCH
INSTALLATION
REFERENCE HOLE
(Subframe side)
REFERENCE HOLE
(Body side)
SUBFRAME
Reference holes alignment
8 x 1.25 mm
26 N·m
(2.7 kgf·m, 20 lbf·ft)
REAR DAMPER
(For some ’05-06 models)
FRONT SUSPENSION
SUBFRAME
After loosening the subframe mounting bolts, be sure to replace them with new ones.
Replace.
05/06/27 18:25:14 61S6M040_200_0124
*01
S6M6A00J20100027165KBAT00
Brace and Gusset
20-124
Frame
Frame Brace and Gusset Replacement
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
To body To body
To body
To body
FRONT STRUT BRACE
RIGHT REAR
DAMPER GUSSET
To body
To body
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
REAR LOWER
ARM BRACE
REAR FLOOR
CROSS MEMBER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
LEFT REAR
DAMPER GUSSET
To body
To body
SIDE FRAME BRACE
To body
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
To body
REAR DAMPER
GUSSETS
REAR LOWER ARM BRACE
(For some ’05-06 models)
FRONT STRUT BRACE
(For some ’05-06 models)
SIDE FRAME BRACE
05/06/27 18:25:14 61S6M040_200_0125
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст