Acura RSX Honda Integra. Manual — part 376
+
−
+
−
01
02
S6M6A22J34200040901MBAT01
01
02
S6M6A22J34200040901KBAT01
+
−
+
−
20-40
20-40
Moonroof
Glass Height Adjustment
Glass Replacement
B
A
2
0.5/
1 mm
(0.08
0.02/
0.04 in.)
Fastener Locations
: Bolt, 6
A
Forward
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
Forward
A
The roof panel (A) should be even with the glass
weatherstrip (B), to within 2
0.5/
1 mm
(0.08
0.02/
0.04 in.) all the way around. If not, make
the following adjustment:
1. Tilt-up the glass.
2. Loosen the bolts on each side, and adjust the glass
(A).
3. If necessary, repeat on opposite side.
4. The side-to-side fit of the glass weatherstrip can be
adjusted by loosening the frame mounting bolts
and moving the frame right or left and forward or
backward by hand (see page 20-43).
1. Tilt-up the glass.
2. Remove the bolts from both sides.
3. Remove the glass (A) by lifting it up. Do not
damage the roof panel.
4. Install the glass in the reverse order of removal,
and adjust the glass height (see page 20-40).
5. Check for water leaks. Use free-flowing water from
a hose without a nozzle. Do not use high-pressure
water.
05/06/27 18:22:58 61S6M040_200_0041
01
S6M6A22J34200041401KBAT02
20-41
Sunshade Replacement
Fastener Locations
: Screw, 2
A
A
B
1. Remove the glass.
2. Remove the screws from the front edges of both
sunshade rails (A).
3. Carefully slide the sunshade (B) forward, then
remove it.
4. Install the sunshade in the reverse order of removal,
and adjust the glass height (see page 20-40).
5. Check for water leaks. Use free-flowing water from
a hose without a nozzle. Do not use high-pressure
water.
05/06/27 18:22:58 61S6M040_200_0042
01
S6M6A22J34200041001KBAT00
20-42
Moonroof
Motor Replacement
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
1. Remove the headliner (see page 20-55).
2. Put on gloves to protect your hands. Disconnect the
connector (A), and remove the bolts, then remove
the motor (B).
3. Install the motor in the reverse order of removal,
and note these items:
• Make sure the connector is plugged in properly.
• Check the motor operation.
05/06/27 18:22:59 61S6M040_200_0043
02
S6M6A22J34200040801KBAT00
20-43
Frame and Drain Tube Replacement
E
: Bolt, 8
G
tape, 6
: Cushion
E
E
E
E
G
G
G
G
G
G
G
G
E
D
A
B
H
B
B
F
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
E
D
C
B
D
Fastener Locations
1. Remove these items:
• Headliner (see page 20-55)
• Moonroof glass (see page 20-40)
2. Put on gloves to protect your hands. Disconnect the motor connector (A) and drain tubes (B), and remove the
interior harness (C) by detaching the harness clips (D) and removing the cushion tape (E).
3. With an assistant holding the frame (F), remove the bolts (G), starting at the rear. Release the rear hooks (H) by
moving the frame forward, then remove the frame.
4. With the help of an assistant, carefully remove the frame through the door opening. Take care not to scratch the
interior trim and body, or tear the seat covers.
(cont’d)
05/06/27 18:22:59 61S6M040_200_0044
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст