Acura RSX Honda Integra. Manual — part 322
01
01
02
03
S6M6A00E16226600000LCAT00
Special Tools Required
Welded type
Double loop type
Low profile type
Inboard Joint Side
16-6
Driveline/Axle
Driveshaft Disassembly
A
B
D
C
E
G
F
• Threaded adapter, 22 x 1.5 mm 07XAC-001010A
• Threaded adapter, 24 x 1.5 mm 07XAC-001020A
• Boot band pincers, Kent-Moore J-35910 or equivalent,
commercially available
• Slide hammer, 5/8’’-18 UNF, commercially available
1. Remove the set ring from the inboard joint.
2. Remove the boot bands. Be careful not to damage
the boot and dynamic damper.
• If the boot band is a welded type (A), cut the boot
band (B).
• If the boot band is a double loop type (C), lift up
the band end (D), then push it into the clip (E).
• If the boot band is a low profile type (F), pinch the
boot band using commercially available boot
band pincers (G).
05/06/27 18:12:38 61S6M040_160_0006
04
05
06
16-7
A
A
B
D
C
B
A
D
E
C
A
3. Make a mark (A) on each roller (B) and inboard joint
(C) to identify the locations of rollers and grooves
in the inboard joint. Then remove the inboard joint
on the shop towel (D). Be careful not to drop the
rollers when separating them from the inboard
joint.
4. Make a mark (A) on the rollers (B) and spider (C) to
identify the locations of rollers on the spider, then
remove the rollers.
5. Remove the circlip (D).
6. Mark the spider and driveshaft (E) to identify the
position of the spider on the shaft.
7. Remove the spider.
8. Wrap the splines on the driveshaft with vinyl tape
(A) to prevent damage to the boot and dynamic
damper.
9. Remove the inboard boot and dynamic damper. Be
careful not to damage the boot and dynamic
damper.
10. Remove the vinyl tape.
(cont’d)
05/06/27 18:12:38 61S6M040_160_0007
01
07
08
02
Outboard Joint Side
Ear clamp type
16-8
Driveline/Axle
Driveshaft Disassembly (cont’d)
A
B
A
A
B
C
K20A3 engine model: 07XAC-001010A
K20A2 engine model: 07XAC-001020A
K20Z1 engine model: 07XAC-001020A
B
A
1. Remove the boot bands (A). Lift up the three tabs
(B) with a screwdriver. Be careful not to damage
the boot and dynamic damper.
2. Slide the outboard boot (A) partially to the inboard
joint side. Be careful not to damage the boot.
3. Wipe off the grease to expose the driveshaft and
the outboard joint inner race.
4. Make a mark (A) on the driveshaft (B) at the same
position of the outboard joint end (C).
5. Carefully clamp the driveshaft in a vise.
6. Remove the outboard joint (A) using the special
tool and a commercially available 5/8’’-18 UNF
slide hammer (B).
7. Remove the driveshaft from the vise.
05/06/27 18:12:39 61S6M040_160_0008
09
03
16-9
A
8. Remove the stop ring from the driveshaft.
9. Wrap the splines on the driveshaft with vinyl tape
(A) to prevent damage to the boot.
10. Remove the outboard boot. Be careful not to
damage the boot.
11. Remove the vinyl tape.
05/06/27 18:12:39 61S6M040_160_0009
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст