Acura RSX Honda Integra. Manual — part 323
01
S6M6A00E16226600000LDAT00
Exploded View
16-10
Driveline/Axle
Driveshaft Reassembly
OUTBOARD BOOT (TPE)
SET RING
INBOARD JOINT
CIRCLIP
ROLLER
SPIDER
INBOARD BOOT
DYNAMIC DAMPER
DRIVESHAFT
STOP RING
EAR CLAMP BANDS
OUTBOARD JOINT
DOUBLE LOOP BAND
DOUBLE LOOP BAND
Right driveshaft
Replace.
Note the direction
of installation.
Replace.
Replace.
Use the grease included in the
inboard boot set.
Replace.
Replace.
Use the grease included in the
inboard boot set.
Use the grease included in the
outboard boot set.
05/06/27 18:12:39 61S6M040_160_0010
02
*01
03
Special Tools Required
Inboard Joint Side
16-11
A
B
C
A
A
B
C
• Boot band tool, KD-3191 or equivalent, commercially
available
• Boot band pincers, Kent-Moore J-35910 or equivalent,
commercially available
NOTE: Refer to the Exploded View as needed during
this procedure.
1. Wrap the splines with vinyl tape (A) to prevent
damage to the inboard boot and dynamic damper.
2. Install the dynamic damper and inboard boot onto
the driveshaft, then remove the vinyl tape. Be
careful not to damage the inboard boot and
dynamic damper.
3. Install the spider (A) onto the driveshaft by aligning
the marks (B) on the spider and the end of the
driveshaft.
4. Install the circlip (C) into the driveshaft groove.
Rotate the circlip in its groove to make sure it is
fully seated.
5. Fit the rollers (A) onto the spider (B) with their high
shoulders facing outward, and note these items:
• Reinstall the rollers in their original positions on
the spider by aligning the marks (C).
• Hold the driveshaft pointed up to prevent the
rollers from falling off.
(cont’d)
05/06/27 18:12:40 61S6M040_160_0011
−
−
04
05
03
06
−
−
−
−
−
−
Grease quantity
Inboard joint:
K20A2 engine model:
150
160 g (5.3
5.6 oz)
K20A3 engine model:
130
140 g (4.6
4.9 oz)
K20Z1 engine model:
150
160 g (5.3
5.6 oz)
16-12
Driveline/Axle
Driveshaft Reassembly (cont’d)
A
A
B
A
6. Pack the inboard joint with the joint grease
included in the new driveshaft set.
7. Fit the inboard joint onto the driveshaft, and note
these items:
• Reinstall the inboard joint onto the driveshaft by
aligning the marks (A) on the inboard joint and
the rollers.
• Hold the driveshaft so the inboard joint is
pointing up to prevent it from falling off.
8. Adjust the inboard joint until the rollers are in the
middle of the joint.
9. Fit the boot ends onto the driveshaft and the
inboard joint, then install the new double loop band
(A) onto the boot.
10. Pull up the slack in the band by hand.
11. Mark a position (A) on the band 10
14 mm
(0.4
0.6 in.) from the clip (B).
Use the grease included in the
inboard boot set.
05/06/27 18:12:41 61S6M040_160_0012
−
−
07
04
08
09
16-13
A
B
C
90 degrees
A
12. Thread the free end of the band through the nose
section of the commercially available boot band
tool KD-3191 or equvialent (A), and into the slot on
the winding mandrel (B).
13. Using a wrench on the winding mandrel of the boot
band tool, tighten the band until the marked spot
(C) on the band meets the edge of the clip.
14. Lift up the boot band tool to bend the free end of
the band 90 degrees to the clip. Center-punch the
clip, then fold over the remaining tail onto the clip.
15. Unwind the boot band tool, and cut off the excess
free end of the band to leave a 5
10 mm (0.2
0.4 in.) tail protruding from the clip.
16. Bend the band end (A) by tapping it down with a
hammer.
NOTE:
• Make sure the band and clip do not interfere with
anything on the vehicle and the band does not
move.
• Remove any grease remaining on the
surrounding surfaces.
17. Repeat steps 9 through 16 for the band on the other
end of the boot, then go to step 18.
(cont’d)
05/06/27 18:12:41 61S6M040_160_0013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст