Acura RSX Honda Integra. Manual — part 197
01
S6M6A01K72100000000BBAT30
How to Troubleshoot Circuits at the ECM
Special Tools Required
13-3
General Troubleshooting Information
A
B
C
07SAZ-001000A
Backprobe set 07SAZ-001000A (2 required)
1. Remove the passenger’s dashboard lower cover
(see page 20-67).
2. Connect the backprobe adapters (A) to the stacking
patch cords (B), and connect the cords to a digital
multimeter (C).
3. Using the wire insulation as a guide for the
contoured tip of the backprobe adapter, gently slide
the tip into the connector from the wire side until it
touches the end of the wire terminal.
05/06/27 18:09:09 61S6M040_130_0003
01
01
S6M6A01E34100041701MDAT00
01
S6M6A01E34100014001FEAT00
Fluid Capacity
1.5 L (1.6 US qt) at fluid change
1.7 L (1.8 US qt) at overhaul
13-4
13-4
Manual Transmission
Transmission Fluid Inspection and
Replacement
Back-up Light Switch Test
A
B
C
D
39 N·m
(4.0 kgf·m, 29 lbf·ft)
A
44 N·m
(4.5 kgf·m, 33 lbf·ft)
29 N·m
(3.0 kgf·m, 22 lbf·ft)
1. Park the vehicle on level ground, and turn the
ignition switch to LOCK (0).
2. Remove the oil filler plug (A) and filler plug washer
(B), check the condition of the fluid, and make sure
it is at the proper level (C).
3. If the fluid is dirty, remove the drain plug (D) and
drain it.
4. Install the drain plug with a new drain plug washer,
and refill the transmission fluid to the proper level.
Always use ACURA Manual Transmission Fluid
(MTF). Using engine oil can cause stiffer shifting
because it does not contain the proper additives.
5. Reinstall the oil filler plug with a new filler plug
washer.
1. Disconnect the back-up light switch connector.
2. Check for continuity between the No. 1 and No. 2
terminals of the back-up light switch 2P connector.
There should be continuity when the shift lever is in
reverse.
3. If necessary, replace the back-up light switch.
Apply liquid gasket (P/N 08718-0001 or 08718-0002)
to threads of the switch, and install the switch on
the transmission housing.
NOTE: Do not install the back-up light switch if too
much time has passed after applying the liquid
gasket (for P/N 08718-0002, no more than
4 minutes, for all others, no more than 5 minutes).
Instead, remove the old residue and reapply the
riquid gusket.
05/06/27 18:09:10 61S6M040_130_0004
01
02
01
S6M6A01E34150100000KAAT00
Special Tools Required
2002-2004 models:
2005-2006 models:
13-5
Transmission Removal
A
B
B
A
C
A
C
D
• Engine hanger adapter EQS00BRSX0
• Engine support hanger, A & Reds AAR-T-12566
• Subframe adapter EQS02C000011
Available through the Honda Tool Equipment
Program 1-888-424-6857.
NOTE: Use fender covers to avoid damaging painted
surfaces.
1. Make sure you have the anti-theft code for the radio,
then write down the customers radio station
presets. Disconnect the negative cable from the
battery first, then disconnect the positive cable
from the battery. Remove the battery.
2. Remove the intake manifold cover (see step 6 on
page 5-2).
3. Remove the air cleaner housing (see step 7 on page
5-2).
4. Remove the intake air duct (see step 8 on page 5-2).
5. Remove the battery base (A).
6. Disconnect the transmission ground cable (B).
7. Disconnect the back-up light switch connector (A),
the vehicle speed sensor (VSS) connector (B), the
reverse lockout solenoid connector (6-speed
model) (C), and the output shaft (countershaft)
speed sensor connector (D).
(cont’d)
05/06/27 18:09:10 61S6M040_130_0005
03
04
05
02
Other models:
2005-2006 model 6-speed models:
13-6
Manual Transmission
Transmission Removal (cont’d)
A
B
8. Remove the cable bracket (A), then disconnect the
cables (B) from the top of the transmission housing.
Carefully remove both cables and the bracket
together to avoid bending the cables.
9. Remove the harness clips.
10. Carefully remove the slave cylinder without
bending the clutch line. Do not press the clutch
pedal once the slave cylinder has been removed.
05/06/27 18:09:11 61S6M040_130_0006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст