Acura RSX Honda Integra. Manual — part 176
01
S6M6A10A20336359401KDAT00
K20A2/K20Z1 engines
11-410
Intake Air System
Throttle Body Removal/Installation
THROTTLE CABLE
22 N·m
(2.2 kgf·m, 16 lbf·ft)
THROTTLE POSITION
(TP) SENSOR
GASKET
IDLE AIR CONTROL
(IAC) VALVE
THROTTLE
BODY
EVAPORATIVE EMISSION (EVAP)
CANISTER PURGE VALVE
THROTTLE
STOP SCREW
THROTTLE
LEVER
NOTE:
• Do not adjust the throttle stop screw.
• After reassembly, adjust the cruise control cable (see page 4-71) and the throttle cable (see page 11-409).
• The throttle position (TP) sensor is not removable.
Replace.
Do not adjust.
There should be
no clearance.
05/06/27 17:42:36 61S6M040_110_0410
02
S6M6A11A20336359401KDAT00
K20A3 engine
11-411
THROTTLE CABLE
22 N·m
(2.2 kgf·m, 16 lbf·ft)
THROTTLE
POSITION
(TP) SENSOR
GASKET
CRUISE CONTROL CABLE
IDLE AIR CONTROL
(IAC) VALVE
THROTTLE
BODY
EVAPORATIVE EMISSION (EVAP)
CANISTER PURGE VALVE
THROTTLE
STOP SCREW
THROTTLE
LEVER
NOTE:
• Do not adjust the throttle stop screw.
• After reassembly, adjust the cruise control cable (see page 4-71) and the throttle cable (see page 11-409).
• The throttle position (TP) sensor is not removable.
Replace.
Do not adjust.
There should be
no clearance.
05/06/27 17:42:37 61S6M040_110_0411
01
02
S6M6A00A20336359401MFAT00
K20A2/K20Z1 engines
K20A3 engine
11-412
Intake Air System
Throttle Body Disassembly/Reassembly
2 N·m
(0.2 kgf·m, 1 lbf·ft)
MAP SENSOR
O-RING
TP SENSOR
THROTTLE BODY
O-RING
IAC VALVE
3.5 N·m
(0.35 kgf·m, 2.5 lbf·ft)
EVAP CANISTER
PURGE VALVE
2 N·m
(0.2 kgf·m, 1 lbf·ft)
MAP SENSOR
O-RING
TP SENSOR
THROTTLE BODY
O-RING
IAC VALVE
3.5 N·m
(0.35 kgf·m, 2.5 lbf·ft)
EVAP CANISTER
PURGE VALVE
Replace.
Replace.
Replace.
Replace.
05/06/27 17:42:37 61S6M040_110_0412
01
S6M6A11A20336334807KBAT00
01
S6M6A11A20336334804KBAT00
11-413
11-413
IMT (IMRC) Valve Position Sensor
Replacement
IMT (IMRC) Valve Replacement
B
C
D
E
A
4 N·m
(0.4 kgf·m, 3 lbf·ft)
E
D
A
C
B
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
1. Remove the two screws (A) and the IMT (IMRC)
position sensor (B).
2. Install the sensor with a new O-ring (C), and make
sure the projection (D) inside the IMT (IMRC) valve
matches up with the groove (E) in the sensor.
1. Remove the intake manifold (see page 9-2).
2. Disconnect the vacuum hose (A), then remove the
bolts (B), and remove the IMT (IMRC) valve
assembly (C).
3. Install the parts in the reverse order of removal
with a new O-rings (D).
NOTE: Make sure the bearing (E) is secured into
place.
05/06/27 17:42:37 61S6M040_110_0413
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст