Acura RSX Honda Integra. Manual — part 385
01
S6M6A00J46127053913MFAT10
Special Tools Required
20-77
Front Seat Disassembly/Reassembly - Driver’s
SEAT-BACK
HOOK
CENTER COVER
CLIP
SEAT CUSHION
FRAME/SEAT
TRACKS
SLIDE LEVER
SCREW
CLIPS
CAP
RECLINE COVER
RECLINE KNOB
HEIGHT HANDLE
SIDE AIRBAG
HARNESS
10 x 1.25 mm
47 N·m
(4.8 kgf·m, 35 lbf·ft)
SPRING
SLIDE LEVER
SLIDE ADJUSTER
SEAT CUSHION
SCREW
RECLINE INNER COVER
CENTER
INNER COVER
HOOK
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the SRS component locations (see page 23-10) and the precautions
and procedures (see page 23-11) before performing repairs or service.
NOTE:
• Take care not to tear the seams or damage the seat covers.
• Put on gloves to protect your hands.
• Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.
• To remove the recline cover on the driver’s seat without manual height adjustment, refer to Front Seat Disassembly/
Reassembly-Passenger’s (see page 20-78).
• For seat cushion removal and installation procedures, refer to Front Seat Cover Replacement (see step 2 on page
20-79).
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat cushion cover, stretch the material evenly over the pad.
• Replace any damaged or stress-whitened clips.
• Push the cover clips into place securely.
Unzip the seat-back cover.
05/06/27 18:23:59 61S6M040_200_0078
01
S6M6A00J46127053914MFAT10
Special Tools Required
20-78
Seats
Front Seat Disassembly/Reassembly - Passenger’s
SEAT-BACK
HOOK
CENTER COVER
BAND
CLIP
BRACKET
(With BOSE sound system)
SLIDE LEVER
SCREW
RECLINE COVER
RECLINE KNOB
SIDE AIRBAG
HARNESS
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
OPDS HARNESS
HOOK
CLIPS
REAR SEAT
ACCESS CABLE
CENTER
INNER
COVER
SEAT CUSHION
BAND
SLIDE ADJUSTER
SPRING
SCREW
SLIDE LEVER
REAR SEAT
ACCESS CABLE
RECLINE INNER
COVER
REAR SEAT
ACCESS CABLE
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the SRS component locations (see page 23-10) and the precautions
and procedures (see page 23-11) before performing repairs or service.
NOTE:
• Take care not to tear the seams or damage the seat covers.
• Put on gloves to protect your hands.
• Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.
• For seat cushion removal and installation procedures, refer to Front Seat Cover Replacement (see step 2 on page
20-79).
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat cushion cover, stretch the material evenly over the pad.
• Adjust the rear seat access cable.
• Make sure the rear seat access cable is connected properly on each portion.
• Replace any damaged or stress-whitened clips.
• Push the cover clips into place securely.
Unzip the seat-back cover.
05/06/27 18:23:59 61S6M040_200_0079
01
02
02
S6M6A00J46127053501KBAT00
Special Tools Required
Seat-back Cover
20-79
Front Seat Cover Replacement
A
B
D
E
E
C
A
B
A
B
C
A
D
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 23-10) and the
precautions and procedures (see page 23-11) before
performing repairs or service.
NOTE:
• Take care not to tear the seams or damage the seat
covers.
• Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
• On the passenger’s seat with side airbag, do not
touch the OPDS sensor in the seat-back pad, and keep
it away from oil. Oil can corrode the sensor, causing it
to fail.
• Put on gloves to protect your hands.
1. Remove the front seat (see page 20-75).
2. From under the seat cushion, detach the side
airbag connector clip (A), and on the passenger’s
seat, detach the OPDS unit connector clip (B).
Release the seat cushion cover (C) from the seat
cushion frame spring (D), then pull the cover back,
and remove the harness bands (E). The passenger’s
seat is shown, the driver’s seat is symmetrical
except it has no OPDS unit connector.
3. Fold the seat-back forward.
4. If equipped with a lumbar support, remove the clip
(A), then remove the lumbar support handle (B).
5. Detach the hooks (A), then remove the front
headrest trim (B) and rear headrest trim (C).
For ’02-04 models: Pull back the seat-back cover (D).
(cont’d)
05/06/27 18:24:00 61S6M040_200_0080
01
02
05
07
’02-04 models
20-80
Seats
Front Seat Cover Replacement (cont’d)
A
B
C
D
A
A
B
C
D
E
A
B
A
A
A
A
B
6. ’05-06 models: Release the hooks (A), and release
the seat-back cover (B) from the wire loop (C) on
the seat-back frame. Release the fasteners (D), and
then pull back the seat-back cover.
7. Release the hook (A), and unzip the seat-back cover
(B). Pull the side airbag harness (C) and the OPDS
harness (D) (passenger’s seat) out through the
holes (E) in the seat cushion cover. The passenger’s
seat is shown, the driver’s seat is symmetrical
except it has no OPDS harness.
8. Remove the side airbag (see page 23-134), and
release the hooks (A) from the airbag module
holder (B).
9. Pull back the edge of the seat-back cover (A) all the
way around, and release the clips (B), then remove
the seat-back cover.
05/06/27 18:24:23 61S6M040_200_0081
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст