Acura RSX Honda Integra. Manual — part 386
03
05
’05-06 models
Inside
Seat Cushion Cover
20-81
A
B
Fastener Location
: Clip, 1
A
10. Install the cover in the reverse order of removal,
and note these items:
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hooks, fasteners
(’05-06 models), and clips.
• Make sure the side airbag harness and OPDS
harness (passenger’s seat) are routed properly.
• Replace any clips you removed with new ones.
Install them with commercially available
upholstery ring pliers.
• If necessary, reinitialize the OPDS control unit
(see page 23-24).
• Always use the proper replacement cover; never
install an aftermarket cover.
1. Remove the front seat (see page 20-75).
2. Remove these items from the front seat:
• Recline cover, driver’s seat (see page 20-77),
passenger’s seat (see page 20-78)
• Front seat belt buckle (see step 5 on page 23-5)
3. From under the seat cushion, detach the side
airbag connector clip, and on the passenger’s seat,
detach the OPDS unit connector clip. Release the
seat cushion cover from the seat cushion frame
spring, then pull the cover back, and remove the
harness bands.
4. Release the hook, and unzip the seat-back cover.
Pull the side airbag harness and the OPDS harness
(passenger’s seat) out through the holes in the seat
cushion cover.
5. Remove the clip, and release the hooks (A).
(cont’d)
05/06/27 18:24:23 61S6M040_200_0082
09
10
11
12
Outside
’02-04 models
20-82
Seats
Front Seat Cover Replacement (cont’d)
A
A
B
C
A
A
B
A
6. From under the seat cushion, release the hooks (A).
If equipped with a seat heater, detach the seat
cushion heater connector clip (B), and remove the
harness band (C).
7. Remove the seat cushion cover (A) with the seat
cushion pad from the seat cushion frame.
8. Pull back the edge of the seat cushion cover all the
way around, and release the clips (A), then remove
the seat cushion cover (B).
05/06/27 18:24:24 61S6M040_200_0083
04
01
01
S6M6A00J46127037901KBAT00
’05-06 models
For Some Models (Driver’s seat)
20-83
20-83
Front Seat Lumbar Support
Replacement
A
B
A
B
A
B
A
9. Install the cover in the reverse order of removal,
and note these items:
• To prevent wrinkles when installing a seat
cushion cover, make sure the material is
stretched evenly over the pad before securing
the clips and hooks.
• Make sure the side airbag harness and OPDS
harness (passenger’s seat) are routed properly.
• Replace any clips you removed with new ones
(A). Install them with commercially available
upholstery ring pliers (B).
SRS components are located in this area. Review the
SRS component locations (see page 23-10) and the
precautions and procedures (see page 23-11) before
performing repairs or service.
NOTE:
• Take care not to tear the seams or damage the seat
covers.
• Put on gloves to protect your hands.
1. Remove the front seat (see page 20-75).
2. From under the seat cushion, detach the side
airbag connector clip. Release the seat cushion
cover from the seat cushion frame spring, then pull
the cover back, and remove the harness bands
(see page 20-79).
3. Release the hook, and unzip the seat-back cover.
Pull the side airbag harness out through the hole in
the seat cushion cover (see page 20-79).
4. Remove the side airbag (see page 23-134).
5. Detach the clips (A) of the airbag module holder (B)
from the seat-back frame.
(cont’d)
05/06/27 18:24:25 61S6M040_200_0084
02
03
20-84
Seats
Front Seat Lumbar Support Replacement (cont’d)
Fastener Locations
: Nut, 3
D
A
C
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
6. Pull away the bottom portion of the seat-back pad
(A) from the seat-back frame (B), and remove the
nuts securing the lumbar support (C). Remove the
bushing (D) and pivot arm from the seat-back frame.
7. Remove the lumbar support (A) as shown.
8. Install the lumbar support in the reverse order of
removal, and note these items:
• Replace the bushing if it’s damaged.
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hook.
• Make sure the side airbag harness is routed
properly.
05/06/27 18:24:25 61S6M040_200_0085
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст