DAF LF45, LF55 Series. Manual — part 656

©

200515

4-15

Removal and installation

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

ΛΦ45/55 series

5

4.11 REMOVAL AND INSTALLATION, F36/F48 FRONT AXLE HUB SEAL

Removing the hub seal
1.

Remove the seal from the hub using the

special tool (DAF no. 1329458). Make sure

that the chamber is not damaged during this.

Installing the hub seal
1.

Fit special tool (A) (DAF no. 1329485) for

the F36 front axle and (DAF no. 1329484)

for the F48 front axle) in the driving tool (B)

(DAF no. 0499809).

2.

Using the special tool, fit the new seal (1) in

the hub (2). The open side of the seal (1)

must face the hub (2). Apply a little grease to

the sealing lip of seal (1).

Drive and chassis

A

B

1

2

S7 00 588

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

4-16

©

200515

Removal and installation

5

ΛΦ45/55 series

4.12 REMOVAL AND INSTALLATION, AUTOMATIC GEARBOX OIL FILTERS

Allison 1000 & 2000 series automatic gearbox

To prevent skin injury, avoid

unnecessary contact with the

drained oil.

Removing the oil filters
1.

Clean the oil filter (1) and filter (5), if present,

as well as the surrounding area.

2.

Loosen the oil filters on the gearbox and heat

exchanger. Collect any oil that is flowing out.

3.

Remove the magnetic rings (2) and (4) and

check them for wear particles.

Note:

If there are larger wear particles in the wear

swarf, this points to advanced wear in the

gearbox. The cause must be tracked down.

4.

Clean the magnetic rings and the contact

surfaces on the gearbox housing and the

heat exchanger.

Installing the oil filters
1.

Fit the magnetic rings (2) and (4) on the

gearbox housing and the heat exchanger.

2.

Lightly lubricate the new oil filter (1) and filter

(5), if present, with clean gearbox oil and

place the oil filters on the gearbox and heat

exchanger.

3.

Tighten the oil filters until they touch the

contact surface. Manually tighten the oil

filters another 360

.

4.

Check the oil level, see chapter "Inspection

and adjustment".

}

1

2

V3 00 480

5

4

6

3

V3 00 556

©

200515

4-17

Removal and installation

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

ΛΦ45/55 series

5

Allison MD 3060 automatic gearbox

Removing the oil filters
1.

Remove the attachment bolts from the filter

covers (2) and remove the filter covers.

Collect any oil that is flowing out.

2.

Remove the oil filters from the oil sump.

3.

Remove the various O-rings and the gasket

from the filter covers.

4.

Remove any traces of gasket from the filter

covers and the contact surfaces.

Installing the oil filters
1.

Lightly lubricate the new O-rings with clean

gearbox oil and fit the various O-rings to the

filter covers.

Note:

Compare the new O-rings to the old O-rings

to ensure that the correct O-rings are used.

2.

Fit a new gasket to the filter covers.

3.

Lightly lubricate the rubber inner ring of the

oil filters with clean gearbox oil and fit the oil

filters to the filter covers.

4.

Fit the filter covers together with the oil filters

to the gearbox and tighten the attachment

bolts to the specified torque, see "Technical

data".

5.

Check the oil level, see chapter "Inspection

and adjustment".

V300371

2

1

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

4-18

©

200515

Removal and installation

5

ΛΦ45/55 series