DAF CF65, CF75, CF85 Series . Manual — part 1038
©
200424
3-11
Removal and installation
SINGLE REAR AXLE 1354
ΧΦ65/75/85 series
8
5
3.7 REMOVAL AND INSTALLATION, PINION OIL SEAL
Removing the pinion oil seal
1.
Remove the drive flange.
2.
Drill two holes into the seal and screw the
special tool (B) (DAF no. 0484899) into the
seal. Pull the oil seal from the pinion housing
using the special tool (A)
(DAF no. 0694928).
Installing the pinion oil seal
1.
Use the special tool (DAF no. 1240088) to fit
the seal so that the inscription "outside" is
pointed outwards.
2.
Fit the drive flange.
A
B
A8 00 426
SINGLE REAR AXLE 1354
3-12
©
200424
Removal and installation
5
ΧΦ65/75/85 series
8
3.8 REMOVAL AND INSTALLATION, DIFFERENTIAL
Removing the differential
1.
Drain the oil from the differential and the
hubs, see Chapter "Draining and filling".
2.
Remove the prop shaft from the drive flange.
3.
Remove the left axle shaft.
4.
Pull the right axle shaft (i.e. on the side
where the differential-gear lock cylinder is
fitted) 15 - 18 cm from the hub.
5.
Remove the air connection for the differential
lock.
6.
Slacken the locking nut of the differential lock
cylinder and turn the differential lock cylinder
out approx. one turn.
7.
Attach the differential securely to a lifting
device.
8.
Remove the attachment bolts from the
differential.
9.
Remove the differential from the axle
housing using two jacking screws.
A800291
1
2
3
4
6 5
7
8
9
1110
12
13
14
15
16
17
18
19
20
21
22
23
24
©
200424
3-13
Removal and installation
SINGLE REAR AXLE 1354
ΧΦ65/75/85 series
8
5
Installing the differential
1.
Install the right axle shaft and slide it into the
selector sleeve of the differential lock
cylinder.
2.
Slacken the engaging cylinder until the
selector sleeve is positioned inside the edge
of the axle housing.
3.
Remove the jacking screws.
4.
Clean the mating surfaces of the banjo
housing and the differential housing and
regrind the surfaces lightly. Do not damage
the mating faces in the process.
5.
Check the stud bolts for signs of damage.
Replace the stud bolts if these are damaged.
Apply locking compound to the new stud
bolts, see "Technical data".
6.
Apply a thin, even layer of sealant to the
mating surface and around the stud bolts of
the banjo housing, see "Technical data".
7.
Fit the differential into the banjo housing.
Evenly tighten the nuts. Tighten the nuts to
the specified tightening torque, see
"Technical data".
8.
Install the left axle shaft and slide both axle
shafts into the differential.
9.
Tighten the engaging cylinder while turning
the right wheel at the same time, until the
teeth of the selector sleeve and the satellite-
gear housing engage.
10. Slacken the engaging cylinder 1.5 turns and
tighten the lock nut to the specified tightening
torque, see "Technical data".
11. Fit the air connection to the differential lock.
12. Fit the prop shaft to the drive flange.
13. Fill the differential and the hubs with oil. See
"Draining and filling".
A800024
A800035
A800034
1,5x
SINGLE REAR AXLE 1354
3-14
©
200424
Removal and installation
5
ΧΦ65/75/85 series
8
3.9 REMOVAL AND INSTALLATION, DIFFERENTIAL LOCK
Removing the differential lock
1.
Remove the differential.
2.
Remove the yoke axle (5) from the yoke (6)
using a home-made yoke puller (A800151).
ø30
ø30
ø16
ø9
M8
165
120
6
A800151
A800026
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст