DAF CF65, CF75, CF85 Series . Manual — part 1004
©
200423
3-17
Removal and installation
STEERED TRAILING SWIVEL AXLE
ΧΦ65/75/85 series
7
7
3.7 REMOVAL AND INSTALLATION, THRUST BEARING, ASSEMBLED VERSION
Removing the thrust bearing, assembled
version
1.
Remove the swivel axle from the axle end.
2.
Tap the entire thrust bearing out of the swivel
axle using a driver. Make sure that no
needles fall from the needle bearings.
Installing the thrust bearing, assembled
version
1.
Fit the thrust bearing in the swivel axle using
a press or a plastic mallet. Make sure that no
needles fall from the needle bearings.
2.
Check that the thrust bearing makes contact
in all places with the swivel axle.
3.
Fit the swivel axle to the axle end.
S7 00 551
S7 00 553
STEERED TRAILING SWIVEL AXLE
3-18
©
200423
Removal and installation
7
ΧΦ65/75/85 series
7
3.8 REMOVAL AND INSTALLATION, NEEDLE BEARINGS
Removing the needle bearings
1.
Remove the swivel axle from the axle end.
2.
Remove the thrust bearing
3.
Use the needle bearing puller, special tool
(DAF no. 0694827), to remove the needle
bearings.
For 182N and 186N axles the additional set,
special tool (DAF no. 0694937), should be
fitted to the needle bearing puller. The
additional set consists of a bush (C) and a
thrust piece (D).
4.
Insert the bush (C) in the needle
bearings (1).
5.
Place the sleeve (B) on the swivel axle ear.
6.
Fit the threaded end (A) into the sleeve (B)
and through bush (C).
7.
Screw the thrust piece (D) on the threaded
spindle, until it abuts bush C.
8.
Pull the needle bearings from the outside to
the inside of the swivel axle (see the arrows
in the drawing). When the needle
bearings (1) are removed from the swivel
axle, the oil seal (2) will also be removed.
9.
The lowest needle bearings (3) are removed
from the swivel axle in the same way (from
the outside to the inside).
Installation of needle bearings
1.
To prevent the needle bearings from
becoming damaged while being inserted,
use special tool (DAF no. 0694827).
For the 182N and 186N axles, the special
tool must be supplemented with special tool
(DAF no. 0694937).
Note:
The needle bearings have different lengths.
The longest needle bearings must be fitted in
the lowest part of the swivel axle.
2.
Apply plenty of grease to the needle
bearings.
S7 00 550
1
2
3
B
C
D
A
©
200423
3-19
Removal and installation
STEERED TRAILING SWIVEL AXLE
ΧΦ65/75/85 series
7
7
3.
To fit the needle bearings in the upper side of
the swivel axle, work in the following manner:
Fit the oil seal (2) with the open side next
to the bush collar pointing towards the
bush (C).
Fit both needle bearings (1) to the bush (C).
4.
Assemble the special tool
(DAF no. 0694827). Press the needle
bearings from the outside to the inside into
the swivel axle, in view of the bevelled sides
of the swivel axle.
5.
Press the needle bearings into the swivel
axle to the specified depth (a), see 'Technical
data'.
Note:
The marked lines on the thrust piece (D) are
not applicable.
6.
The lowest needle bearings are fitted to the
swivel axle in the same way (from the outside
to the inside).
7.
Press the needle bearings into the swivel
axle to the specified depth (b), see 'Technical
data'.
8.
Fit the thrust bearing.
9.
Fit the swivel axle to the axle end.
S7 00 548
1
2
B
C
D
A
;;
;;
;;
;;
;;
;;;;;;
;;;;;;
;
;
;;
;;
;;
;;
;;
;;
;
;
;
;
;;;
;;;
;;;
;;;
;;;
;;;
;
;;
;;
;
;
;
;;;
;;;
;;;
;;;
;
;;
;;
;;
;;
;;
;;
;;
;;
;;
S7 00 710
a
b
STEERED TRAILING SWIVEL AXLE
3-20
©
200423
Removal and installation
7
ΧΦ65/75/85 series
7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст