DAF CF65, CF75, CF85 Series . Manual — part 1165
©
200423
4-1
Removal and installation
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ75 series
5
4. REMOVAL AND INSTALLATION
4.1 REMOVAL AND INSTALLATION, INTERIOR FILTER ELEMENT
Removing interior filter
1.
Open the grille.
2.
Push the locknut on the filter casing to one
side and remove the filter element.
Fitting interior filter
1.
Fit the filter element.
2.
Push the filter element into the locknut on the
filter casing.
3.
Close the grille.
Engine, cooling system and fuel system
K1 01 033
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
4-2
©
200423
Removal and installation
5
ΧΦ75 series
4.2 REMOVAL AND INSTALLATION, AIR FILTER ELEMENT
Removing the air filter element
1.
Loosen all the clamping brackets (1) of the
air filter cover (2).
2.
Remove the air filter cover (2).
3.
Remove the air filter element (3).
4.
Clean the inside of the air filter housing and
the air filter cover.
5.
When replacing the air filter element, reset
the air filter indicator, if fitted, by pressing the
button on the indicator.
i400443
1
5
2
4
3
i400869
©
200423
4-3
Removal and installation
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
ΧΦ75 series
5
Installing the air filter element
1.
Fit the air filter element (3) in the air filter
housing.
2.
Fit the air filter cover. Note the arrow (4) on
the air filter cover (2).
3.
Fit all the clamping brackets (1).
4.
Check that the flexible sealing bellows (5) on
the air intake is not damaged. Replace if
necessary.
i400443
1
5
2
4
3
EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES
4-4
©
200423
Removal and installation
5
ΧΦ75 series
4.3 REMOVAL AND INSTALLATION, COOLANT FILTER
When the coolant is hot, there is an
overpressure in the cooling system.
Carefully remove the filler cap to
release the overpressure.
Do not remove the filler cap when the
engine is running.
Coolant is a toxic fluid. Contact with
the skin should therefore be
avoided.
In the event of contact with the skin:
remove the liquid with paper or a
cloth, wash with soap and water. If
irritation persists, consult a doctor.
If swallowed: DO NOT induce
vomiting. Rinse mouth, drink two
glasses of water and consult a
doctor.
In the event of inhalation: get fresh
air and rest.
In order to avoid damaging the
cylinder block, do not top up a warm
engine with coolant.
Removing the coolant filter
1.
Place a tray beneath the coolant filter to
collect any escaping coolant.
2.
Remove the filler cap from the expansion
tank.
3.
Turn the shut-off valve (1) clockwise to the
"C" position.
4.
Remove the coolant filter by turning it
counter-clockwise.
Installing the coolant filter
1.
Clean the sealing face of the coolant filter.
2.
Apply a small amount of coolant to the
sealing ring of the coolant filter.
3.
Fit the coolant filter so that the sealing ring
makes contact. Then tighten the filter by
hand
∂ to • of a turn.
4.
Turn shut-off valve (1) anti-clockwise to the
"O" position.
5.
Fit the filler cap on the expansion tank.
6.
Run the engine and check that the coolant
filter seals correctly.
7.
Check the coolant level.
}
O
1
C
M200372
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст