Honda Ridgeline. Manual — part 547
In-vehicle
24-13
1. Check that the seat belt is not twisted or caught on
anything.
2. After installing the anchors, check for free
movement on the anchor bolts. If necessary,
remove the anchor bolts and check that the
washers and other parts are not damaged or
improperly installed.
3. Check the seat belts for damage or discoloration.
Clean with a shop towel if necessary. Use only
soap and water to clean.
NOTE: Dirt buildup in the loops of the upper
anchors can cause the seat belts to retract slowly.
Wipe the inside of the loops with a clean cloth
dampened in isopropyl alcohol.
4. Check that the seat belt does not lock when pulled
out slowly. The seat belt is designed to lock only
during a sudden stop or impact.
5. Make sure that the seat belt will retract
automatically when released.
6. For front and rear passenger’s seat belts, check the
seat belt retractor locking mechanism ALR
(automatic locking retractor). This function is for
securing child seats:
–1 Pull the seat belt all the way out to engage the
ALR. The seat belt should retract with a soft,
ratcheting sound, but not extend. This is
normal.
–2 To disengage the ALR, release the seat belt and
allow it to fully retract, then pull the seat belt
out part-way. The seat belt should retract and
extend normally.
7. Replace the seat belt with a new assembly if there
is any abnormality. Do not disassemble any part of
the seat belt for any reason.
*01
SJC8A00H46400000000DAAT00
24-14
SRS
Component Location Index
SIDE AIRBAG
CUTOFF INDICATOR
SRS INDICATOR
CABLE REEL
DRIVER’S AIRBAG
FRONT PASSENGER’S AIRBAG
SRS UNIT
OPDS SENSOR/
SEAT-BACK
FRONT PASSENGER’S
SIDE AIRBAG
FRONT PASSENGER’S
SEAT BELT TENSIONER
RIGHT SIDE
IMPACT SENSOR (FIRST)
ROLL RATE SENSOR
OPDS UNIT (’06 Model)
DRIVER’S SEAT BELT TENSIONER
LEFT SIDE IMPACT SENSOR (FIRST)
DRIVER’S SIDE AIRBAG
MEMORY ERASE
SIGNAL (MES)
YELLOW CONNECTOR (2P)
(Used for erasing SRS
DTCs without the HDS)
DATA LINK
CONNECTOR
(DLC) 16P
FRONT PASSENGER’S WEIGHT SENSORS
(’07-08 Models)
ODS UNIT (’07-08 Models)
DRIVER’S SEAT POSITION SENSOR (’07-08 Models)
PASSENGER’S AIRBAG CUTOFF INDICATOR (’07-08 Models)
Troubleshooting, page 24-169
Replacement, page 24-185
Replacement, page 24-174
Disposal, page 24-181
Replacement, page 24-175
Disposal, page 24-181
Replacement, page 24-188
Replacement,
page 20-111
Replacement,
page 24-176
Disposal,
page 24-181
Replacement,
page 24-4
Disposal,
page 24-181
Replacement, page 24-189
Replacement, page 24-194
Initialization, page 24-30
Replacement, page 24-192
Replacement, page 24-4
Disposal, page 24-181
Replacement, page 24-189
Replacement,
page 24-176
Disposal,
page 24-181
Replacement, page 24-191
Initialization, page 24-30
Calibration, page 24-31
Operation Check, page 24-32
Replacement, page 24-192
Operation Check, page 24-33
Replacement, page 24-195
Bulb Test, page 24-196
*02
24-15
RIGHT SIDE CURTAIN AIRBAG
LEFT SIDE CURTAIN AIRBAG
LEFT SIDE IMPACT SENSOR (SECOND)
RIGHT SIDE IMPACT SENSOR (SECOND)
LEFT FRONT IMPACT SENSOR
RIGHT FRONT IMPACT SENSOR
Replacement, page 24-177
Disposal, page 24-181
Replacement, page 24-177
Disposal, page 24-181
Replacement, page 24-190
Replacement, page 24-190
Replacement, page 24-193
Replacement, page 24-193
01
SJC8A00H46400000000AAAT00
General Precautions
Steering-related Precautions
Cable Reel Alignment
24-16
SRS
Precautions and Procedures
Please read the following precautions carefully before
servicing the airbag system. Observe the instructions
described in this manual, or the airbags could
accidentally deploy and cause damage or injuries.
• Except when doing electrical inspections, always turn
the ignition switch OFF, ground the SCS line with the
HDS to take the PCM out of active status, disconnect
the negative cable from the battery, and wait at least
3 minutes before beginning work.
NOTE: The SRS memory is not cleared even if the
ignition switch is turned OFF or the battery cables are
disconnected from the battery.
• Use replacement parts which are manufactured to the
same standards and quality as the original parts. Do
not install used SRS parts. Use only new parts when
making SRS repairs.
• Carefully inspect any SRS part before you install it.
Do not install any part that shows signs of being
dropped or improperly handled, such as dents, cracks
or deformation.
• Before removing any of the SRS parts (including the
disconnection of the connectors), always disconnect
the SRS connector.
• Use only a digital multimeter to check the system. If it
is not a Honda multimeter, make sure its output is
10 mA (0.01 A) or less when switched to the lowest
value in the ohmmeter range. A tester with a higher
output could cause accidental deployment and
possible injury.
• Do not put objects on the front passenger’s airbag.
• The original audio system and navigation system has
a coded theft protection circuit. Be sure to get the
anti-theft code and write down the XM audio presets
(if equipped) before disconnecting the negative cable
from the battery.
• Before returning the vehicle to the customer, enter
the audio system and the navigation system code (if
equipped), then enter the XM audio presets (if
equipped); set the clock on vehicles without
navigation.
• Misalignment of the cable reel could cause an open in
the wiring, making the SRS system, remote steering
wheel controls, and the horn inoperative. Center the
cable reel whenever the following is performed (see
step 6 on page 24-187).
– Installation of the steering wheel
– Installation of the cable reel
– Installation of the steering column
– Other steering-related adjustment or installation
• Do not disassemble the cable reel.
• Do not apply grease to the cable reel.
• If the cable reel shows any signs of damage, replace
it with a new one. For example, if it does not rotate
smoothly, replace the cable reel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст