Honda Ridgeline. Manual — part 271
01
SJC8A00E16226600000LDAT00
Exploded View
16-10
Driveline/Axle
Front Driveshaft Reassembly
SET RING
INBOARD JOINT
(Left driveshaft)
SNAP
RING
SPIDER
INBOARD BOOT
OUTBOARD BOOT
OUTBOARD JOINT
DRIVESHAFT
DOUBLE LOOP BANDS
EAR CLAMP BANDS
CIRCLIP
LOCKING TAB BAND
(Right driveshaft)
ROLLER
Replace.
Replace.
(Boot band replacement only.)
Replace.
Replace.
Replace.
Use the grease included
in the inboard boot set.
Use the grease included
in the inboard boot set.
Use the grease included
in the outboard boot set.
02
03
04
05
Special Tools Required
Double loop type
Locking tab type
Inboard Joint Side
16-11
A
A
B
B
C
A
C
A
B
• Boot band tool, KD-3191 or equivalent, commercially
available
• Boot band pliers, Kent-Moore J-35910 or equivalent,
commercially available
NOTE: Refer to the Exploded View as needed during
this procedure.
1. Wrap the splines with vinyl tape (A) to prevent
damage to the inboard boot.
2. Install the inboard boot and boot band (B) on the
driveshaft, then remove the vinyl tape. Be careful
not to damage the inboard boot.
3. Install the spider (A) onto the driveshaft by aligning
the marks (B) on the spider and the end of the
driveshaft.
4. Fit the snap ring (C) into the driveshaft groove.
Always rotate the snap ring in its groove to make
sure it is fully seated.
5. Fit the rollers (A) onto the spider (B) with their high
shoulders facing outward, and note these items:
• Reinstall the rollers in their original positions on
the spider by aligning the marks (C).
• Hold the driveshaft pointed up to prevent the
rollers from falling off.
(cont’d)
−
−
06
07
01
02
−
−
−
−
−
Grease quantity
’06 model
Inboard joint: 210
230 g (7.4
8.1 oz)
’07
08 models
Inboard joint: 190
210 g (6.7
7.4 oz)
16-12
Driveline/Axle
Front Driveshaft Reassembly (cont’d)
A
Front
A
C
B
A
B
6. Pack the inboard joint with the joint grease
included in the new driveshaft set.
7. Fit the inboard joint onto the driveshaft, and note
these items:
• Reinstall the inboard joint onto the driveshaft by
aligning the marks (A) on the inboard joint and
the rollers.
• Hold the driveshaft so the inboard joint points up
to prevent it from falling off.
8. Install the boot bands.
• For the double loop type, go to step 9.
(Boot band replacement only.)
• For the locking tab type, go to step 18.
9. Fit the boot ends onto the driveshaft and the
inboard joint, then install the new double loop band
(A) onto the boot (B).
NOTE: Pass the end of the new double loop band
through the clip (C) twice in the direction of the
forward rotation of the driveshaft.
10. Pull up the slack in the band by hand.
11. Mark a position (A) on the band 10
14 mm
(0.4
0.6 in.) from the clip (B).
Use the grease included
in the inboard boot set.
−
−
03
04
05
06
16-13
C
B
A
90 degrees
A
A
12. Thread the free end of the band through the nose
section of a commercially available boot band tool
KD-3191 or equivalent (A), and into the slot on the
winding mandrel (B).
13. Place a wrench on the winding mandrel of the boot
band tool, and tighten the band until the marked
spot (C) on the band meets the edge of the clip.
14. Lift up the boot band tool to bend the free end of
the band 90 degrees to the clip. Center-punch (A)
the clip, then fold over the remaining tail onto the
clip.
15. Unwind the boot band tool, and cut off the excess
free end of the band to leave a 5
10 mm
(0.2
0.4 in.) tail protruding from the clip.
16. Bend the band end (A) by tapping it down with a
hammer.
NOTE:
• Make sure the band and clip do not interfere with
anything, and the band does not move.
• Remove any grease remaining on the
surrounding surfaces.
17. Repeat steps 9 through 16 for the band on the other
end of the boot, then go to step 20.
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст