Honda Ridgeline. Manual — part 217
01
02
03
04
SJC8A00E10411412287KBAT77
14-253
Shift Lever Knob Replacement
A
B
C
D
A
A
B
A
B
1. Remove the shift lever assembly (see page 14-243).
2. Remove the harness clamps from the shift lever
bracket, and remove the harnesses from the
harness clamps.
3. Pry up the lock covers (A) of the D3 switch/shift lock
solenoid/park pin switch connector (B).
4. Remove the terminal from the connector by
pushing the lock tab (C) up in the connector using a
thin blade screwdriver (D). Remove all six terminals,
and replace the connector.
5. Pry off the shift lever knob ring (A), and remove it.
6. Unlatch the D3 switch harness clamp on the shift
lever bracket, pry out the D3 switch (B), and pull it
from the knob.
7. Remove the D3 switch harness terminals by prying
the lock tabs up with a thin blade screwdriver.
8. Pull the D3 switch harness wires (A) from shift lever
bracket side, and remove the harness wires. Leave
the harness tube (B) and remove only the wires.
(cont’d)
05
06
07
08
14-254
Automatic Transmission
Shift Lever Knob Replacement (cont’d)
A
B
C
9. Remove the shift lever knob from the shift lever.
10. Install a new shift lever knob on the shift lever.
11. Insert the new D3 switch harness wires (A) in the
original harness tube (B), then tie a string (C)
around the tube to secure the terminals in the tube.
12. Pull the old tube out of the shift lever knob side to
install the D3 switch harness wires.
13. Remove the old harness tube from the D3 switch
harness terminals.
14. Install the D3 switch harness terminals in the new
D3 switch. Either harness terminal can be installed
in either cavity.
09
10
11
12
14-255
C
B
A
A
B
C
D
E
E
B
A
C
A
B
C
D
E
B
15. Install the D3 switch (A) in the shift lever knob (B).
16. Install the new shift lever knob ring (C).
17. Install the RED harness terminal (A) of the shift lock
solenoid in the No. 5 cavity, and the BLK harness
terminal (B) in the No. 6 cavity.
18. Install the D3 switch harness terminals (WHT) (C) in
the No. 3 and No. 4 cavities. Either D3 switch
harness terminal can be installed in the No. 3 and
No. 4 cavities.
19. Install the park pin switch harness terminals (BLK)
(D) in the No. 1 and No. 2 cavities. Either park pin
switch harness terminal can be installed in the
No. 1 and No. 2 cavities.
20. Make sure that all six terminals lock securely, then
install the lock covers (E) securely in place.
21. Install the D3 switch harness (A) in the harness
clamp (B) at the mark (C).
22. Route the harnesses (A) through the guides (B).
23. Align the marks (C) on each harness, and tie the
harness together into bundle with a new harness
clamp (D) over the marks.
24. Tie the harness together into bundle with a new
harness clamp, then install the harness clamp (E)
on the shift lever bracket.
25. Install the shift lever assembly (see page 14-245).
26. Check that the D3 switch operates.
Terminal side of male terminals
01
02
03
04
SJC8A00E10411412279KBAT00
14-256
Automatic Transmission
Shift Lever Link Replacement
A
B
C
D
A
B
A
B
C
D
F
G
E
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
C
D
1. Remove the driver’s dashboard lower cover
(see page 20-83).
2. Shift the transmission into the R position.
3. Slide the lock tab (A) on the shift cable end holder
(B) toward the shift cable socket holder.
4. Grasp the shift cable lock (C) in the middle with
angle-jaw needle-nose pliers (D), and remove it
from the shift cable end and shift cable end holder.
Do not pry the shift cable lock with a screwdriver, it
may damage the shift cable end holder.
5. Separate the shift cable end (A) from the shift cable
end holder (B).
6. Rotate the socket holder (A) on the shift cable (B) a
quarter turn; the tab (C) on the socket holder will be
in the opening (D) of the socket holder bracket (E).
Then slide the holder to remove the shift cable
from the socket holder bracket. Do not remove the
shift cable by twisting the shift cable guide (F) and
damper (G).
7. Remove the self-locking nut (A) securing the shift
lever link (B) and washer (C), and remove the shift
lever link. Do not drop and lose the shift lever link
bushing (D).
8. Apply silicone grease to the sliding areas between
the shift lever link and shift lever bracket.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст