Honda Ridgeline. Manual — part 229
00
SJC8A00E10411313016KBAT00
14-301
Secondary Shaft ATF Feed Pipe Cap, Feed Pipe Replacement
A
B
C
D
F
G
E
H
1. Remove the ATF feed pipe cap from the
transmission housing (see page 14-300).
2. Remove the snap ring (A) from the feed pipe cap
(B), then remove the feed pipe guide (C), the
O-rings (D) (E), and the 1st clutch ATF feed pipe (F).
3. Replace the 1st clutch ATF feed pipe or the 1st-hold
clutch ATF feed pipe/ATF feed pipe cap assembly.
The 1st-hold clutch ATF feed pipe/ATF feed pipe
cap is not available separately.
4. Install the new O-ring (D) over the 1st clutch ATF
feed pipe, then install the feed pipe over the 1st-
hold clutch ATF feed pipe (G) while aligning the
feed pipe tabs (H) with the guide in the cap.
5. Install the new O-ring (E) in the cap and feed pipe
guide, then secure the guide with the snap ring.
01
SJC8A00E10411239511KAAT01
−
−
01
02
SJC8A00E10411239511KCAT02
Special Tools Required
Special Tools Required
14-302
14-302
Transmission Housing
Mainshaft Bearing Removal
Mainshaft Bearing Installation
07749-0010000
07NAD-PX40100
07749-0010000
A
07NAD-PX40100
A
B
• Driver 07749-0010000
• Attachment, 78 x 80 mm 07NAD-PX40100
1. To remove the mainshaft bearing, expand the snap
ring with snap ring pliers, then push the bearing
out. Do not remove the snap ring unless it’s
necessary to clean the groove in the housing.
• Driver 07749-0010000
• Attachment, 78 x 80 mm 07NAD-PX40100
1. Install the bearing (A) in the direction shown.
2. Expand the snap ring with snap ring pliers, and
insert the bearing part-way into the housing.
3. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
4. After installing the bearing, check that the snap ring
(A) is seated in the bearing and housing groove,
and that the ring end gap (B) is 0
7 mm (0
0.28 in.).
01
02
SJC8A00E10412435143KBAT01
01
02
SJC8A00E10400045011KBAT02
Special Tools Required
Special Tools Required
14-303
14-303
Intermediary Shaft Bearing
Replacement
Park Lever Shaft Bearing
Replacement
07936-3710100
07741-0010201
07936-3710600
07749-0010000
07746-0010200
07741-0010201
07936-GE00100
07936-GE00200
07749-0010000
07746-0010800
• Bearing remover shaft set, 20 mm 07936-3710600
• Bearing remover shaft handle 07936-3710100
• Sliding hammer weight 07741-0010201
• Driver 07749-0010000
• Attachment, 37 x 40 mm 07746-0010200
1. Remove the intermediary shaft bearing from the
transmission housing with the bearing remover
shaft set (20 mm), sliding hammer weight, and
bearing remover shaft handle.
2. Install the new bearing until it bottoms in the
transmission housing with the driver and
attachment (37 x 40 mm).
• Bearing remover shaft, 10 mm 07936-GE00100
• Bearing remover head, 10 mm 07936-GE00200
• Sliding hammer weight 07741-0010201
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-0010800
1. Remove the park lever shaft bearing from the
transmission housing with the bearing remover
head (10 mm), bearing remover shaft (10 mm), and
sliding hammer weight.
2. Install the new bearing until it bottoms in the
transmission housing with the driver and
attachment (22 x 24 mm).
01
02
SJC8A00E10410417254KBAT01
01
02
SJC8A00E10410417256KBAT02
Special Tools Required
Special Tools Required
14-304
14-304
Transmission Housing
Selector Control Shaft Bearing
Replacement
Selector Control Shaft Oil Seal
Replacement
07936-GE00200
07936-GE00100
07741-0010201
07746-0010800
07749-0010000
07749-0010000
07746-0010800
• Bearing remover shaft, 10 mm 07936-GE00100
• Bearing remover head, 10 mm 07936-GE00200
• Sliding hammer weight 07741-0010201
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-0010800
1. Remove the control shaft bearing from the
transmission housing with the bearing remover
head (10 mm), bearing remover shaft (10 mm), and
sliding hammer weight.
2. Install the new bearing until it bottoms in the
transmission housing with the driver and
attachment (22 x 24 mm).
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-0010800
1. Remove the oil seal from the transmission housing.
2. Install the new oil seal in the transmission housing
with the driver and attachment (22 x 24 mm).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст