Honda Ridgeline. Manual — part 587
04
05
06
07
Checking and Adjusting the Headliner/Pillar
Trim Overlap
24-173
A
B
MASKING TAPE
EDGE OF HEADLINER
LESS THAN
15 mm (0.6 in.)
To prevent the side curtain airbag from deploying and
damaging the pillar trim, the overlap between the
headliner and pillar trim must be less then 15 mm. To
check the overlap, do this:
1. Install the headliner (A) and the pillar trim (B).
2. Using masking tape on the headliner, mark the
upper edge of each pillar trim.
3. Remove the pillar trim, and measure the headliner
overlap.
• If the overlap is less than 15 mm, remove the
tape, and install the pillar trim.
• If the overlap is more than 15 mm, go to step 4.
4. Carefully trim the headliner with a utility knife,
reducing the overlap to less than 15 mm.
5. Remove the tape, and install the pillar trim.
01
02
03
04
SJC8A00H46400012802KBAT00
Removal
Installation
24-174
SRS
Driver’s Airbag Replacement
A
B
B
A
B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
A
1. Disconnect the negative cable from the battery,
then wait 3 minutes before starting work.
2. Remove the access panel (A) from the steering
wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Using a TORX T30 bit, remove the two TORX bolts
(A).
4. Disconnect the horn switch connector (1P), then
remove the driver’s airbag (B).
1. Place the new driver’s airbag (A) in the steering
wheel, and secure it with new TORX bolts (B).
2. Connect the cable reel to the driver’s airbag 4P
connector (A), then install the access panel (B) on
the steering wheel.
3. Reconnect the negative cable to the battery.
4. After installing the airbag, confirm proper system
operation:
• Turn the ignition switch ON (II); the SRS indicator
should come on for about 6 seconds and then go
off.
• Make sure the horn button works.
01
02
03
04
SJC8A00H46400012803KBAT00
Removal
Installation
24-175
Front Passenger’s Airbag Replacement
A
B
A
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
A
1. Disconnect the negative cable from the battery,
then wait 3 minutes before starting work.
2. Remove the glove box (see page 20-85).
3. Disconnect the front passenger’s airbag 4P
connector (A) from the dashboard wire harness.
4. Remove the three mounting nuts (A) from the
bracket. Cover the lid and dashboard with a cloth,
and pry carefully with a screwdriver to lift the front
passenger’s airbag (B) out of the dashboard.
NOTE: The airbag lid has pawls on each side which
attach it to the dashboard.
1. Place the new front passenger’s airbag (A) into the
dashboard. Tighten the front passenger’s airbag
mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector
(A) to the dashboard wire harness, then reinstall
the glove box.
3. Reconnect the negative cable to the battery.
4. After installing the airbag, confirm proper system
operation: Turn the ignition switch ON (II); the SRS
indicator should come on for about 6 seconds and
then go off.
01
*01
*02
SJC8A00H46400055381KBAT00
Removal
Installation
24-176
SRS
Side Airbag Replacement
A
A
B
C
A
B
6.3 N·m
(0.64 kgf·m,
4.65 lbf·ft)
1. Disconnect the negative cable from the battery,
then wait 3 minutes before starting work.
2. Disconnect the side airbag harness 2P
connector (A).
3. Remove the seat assembly (see page 20-97) and
seat-back cover (see page 20-111).
NOTE: If you are replacing a deployed airbag,
replace the reinforcing cloth rear hooks (A).
4. Remove the mounting nut (B) and the side
airbag (C).
NOTE:
• If the side airbag lid is secured by a tape, remove the
tape.
• Do not open the lid of the side airbag cover.
• Use new mounting nut tightened to the specified
torque.
• Make sure that the seat-back cover is installed
properly. Improper installation may prevent proper
deployment.
• Be sure to install the harness wires so that they are
not pinched or interfering with other parts.
1. Place the new side airbag on the seat-back frame
(A). Tighten the side airbag mounting nut (B).
2. Install the seat-back cover in the reverse order of
removal (see page 20-111).
NOTE: If you are replacing a deployed airbag,
replace the reinforcing cloth rear hooks.
3. Install the seat assembly (see page 20-97), then
connect the side airbag harness 2P connector.
4. Reconnect the negative cable to the battery.
5. Move the front seat and the seat-back through their
full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
6. Connect the HDS, and clear the DTCs (see page
24-28).
7. After installing the side airbag, confirm proper
system operation: Turn the ignition switch ON (II);
the SRS indicator should come on for about
6 seconds and then go off.
Replace.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст