Honda CR-V (2022 year). Manual in english — page 6
uu
Child Safety
u
Safety of Larger Children
92
Safe Driving
If a lap/shoulder seat belt cannot be used
properly, position the child in a booster seat in
the rear seat. For the child’s safety, check that
the child meets the booster seat
manufacturer’s recommendations.
A backrest is available for a specific booster
seat. Install the backrest to the booster seat
and adjust it to the vehicle seat according to
the booster seat manufacturer’s instructions.
Make sure the seat belt is properly routed
through the guide at the shoulder of the
backrest and the belt does not touch and
cross the child’s neck.
■
Booster Seats
1
When installing a booster seat, make sure to read the
instructions that came with it, and install the seat
accordingly.
There are high- and low-type booster seats. Choose a
booster seat that allows the child to wear the seat
belt correctly.
We recommend a booster seat with a backrest as it is
easier to adjust the shoulder belt.
Guide
93
uu
Child Safety
u
Safety of Larger Children
Safe Driving
Your vehicle has a rear seat where children can be properly restrained. If you ever
have to carry a group of children, and a child must ride in front:
•
Make sure you read and fully understand the instructions and safety information
in this manual.
•
Move the front passenger seat as far back as possible.
•
Have the child sit upright and well back in the seat.
•
Check that the seat belt is properly positioned so that the child is secure in the
seat.
■
Monitoring child passengers
We strongly recommend that you keep an eye on child passengers. Even older, more
mature children sometimes need to be reminded to fasten their seat belts and sit up
properly.
■
Protecting Larger Children - Final Checks
94
Safe Driving
Exhaust Gas Hazard
Carbon Monoxide Gas
The engine exhaust from this vehicle contains carbon monoxide, a colourless,
odourless, and highly toxic gas. As long as you properly maintain your vehicle,
carbon monoxide gas will not get into the interior.
■
Have the exhaust system inspected for leaks whenever
•
The exhaust system is making an unusual noise.
•
The exhaust system may have been damaged.
•
The vehicle is raised for an oil change.
When you operate a vehicle with the tailgate open, airflow can pull exhaust gas into
the interior and create a hazardous condition. If you must drive with the tailgate
open, open all the windows and set the climate control system as shown below.
1.
Select the fresh air mode.
2.
Select the
mode.
3.
Set the fan speed to high.
4.
Set the temperature control to a comfortable setting.
Adjust the climate control system in the same manner if you sit in your parked
vehicle with the engine running.
1
An enclosed area such as a garage can quickly fill up
with carbon monoxide gas.
Do not run the engine with the garage door closed.
Even when the garage door is open, drive out of the
garage immediately after starting the engine.
3
WARNING
Carbon monoxide gas is toxic.
Breathing it can cause unconsciousness and
even kill you.
Avoid any enclosed areas or activities that
expose you to carbon monoxide.
95
Safe Driving
Safety Labels
Label Locations
These labels are in the locations shown. They warn you of potential hazards that can cause serious injury or death. Read these labels
carefully.
If a label comes off or becomes hard to read, contact a dealer for a replacement.
Reserve Tank Cap
Reserve Tank Cap Danger Label
2
P. 687
Sun Visor
Child Safety/SRS Airbag
(Left-hand drive type)
2
P. 71
Battery Danger Label
2
P. 715
Passenger Front Airbag Off
System Label
(Left-hand drive type)
2
P. 62
Sun Visor
Child Safety/SRS Airbag
(Right-hand drive type)
2
P. 71
Air Conditioner Label
2
P. 718
Passenger Front Airbag Off
System Label
(Right-hand Drive Type)
2
P. 62
Front Bulkhead Cover
Front Bulkhead Cover Label
2
P. 680
Rear Head Restraint Label
2
P. 261, 262
Wireless Charger
*
2
P. 286
* Not available on all models
97
Instrument Panel
This chapter describes the buttons, indicators, and gauges that are used while driving.
Driver Information Interface Warning and
Information Messages. . . . . 122
Gauges. . . . . . . . . . . 146
Driver Information Interface . . . . 147
Head-Up Display
* Not available on all models
98
In
strum
e
nt Pa
nel
Indicators
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Parking Brake
and Brake
System Indicator
(Red)
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off if the parking
brake has been released.
•
Comes on when the parking brake is
applied and goes off when it is
released.
•
Comes on when the brake fluid level
is low.
•
Comes on if there is a problem with
the brake system.
•
The beeper sounds and the indicator
comes on if you drive with the
parking brake not fully released.
•
Comes on while driving
- Make sure
the parking brake is released. Check the
brake fluid level.
2
What to do when the indicator
comes on while driving
•
Comes on along with the parking
brake and brake system indicator
(amber)
- Immediately stop in a safe
place. Contact a dealer for repair. The
brake pedal becomes harder to operate.
Depress the pedal further than you
normally do.
•
Comes on along with the ABS
indicator
- Have your vehicle checked
by a dealer.
2
If the Brake System Indicator (Red)
Comes On or Blinks
(Red)
99
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Parking Brake
and Brake
System Indicator
(Red)
•
Comes on for about 15 seconds
when you pull the electric parking
brake switch while the ignition
switch is in LOCK
(
0
*1
.
•
Stays on for about 15 seconds when
you turn the ignition switch to LOCK
(
0
*1
while the electric parking brake
is set.
•
Blinks and the parking brake and
brake system indicator (amber)
comes on at the same time
- There is
a problem with the electric parking
brake system. The parking brake may
not be set.
Avoid using the parking brake and have
your vehicle checked by a dealer
immediately.
2
—
Automatic Brake
Hold System
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Comes on when the automatic
brake hold system is on.
2
Automatic Brake
Hold Indicator
●
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
●
Comes on when the automatic brake
hold is activated.
2
—
(Red)
100
uu
Indicators
u
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Parking Brake
and Brake
System Indicator
(Amber)
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Comes on if there is a problem with
a system related to braking other
than the conventional brake system.
•
Comes on if there is a problem with
the electric parking brake system or
the automatic brake hold system.
•
Stays on constantly
- Have your
vehicle checked by a dealer.
•
Comes on while driving
- Avoid using
the parking brake and have your vehicle
checked by a dealer immediately.
•
Comes on if the parking brake and
brake system is deactivated
temporarily after the battery has
been disconnected, then
reconnected.
•
Drive a short distance at more than 20
km/h (12 mph). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
•
Comes on if there is a problem with
the radar sensor.
•
Indicator may come on temporarily
when the Maximum Load Limit is
exceeded.
•
Make sure the total load is within the
Maximum Load Limit.
2
P. 499
•
Stays on constantly
- Have your
vehicle checked by a dealer.
—
(Amber)
101
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Low Oil Pressure
Indicator
•
Comes on when you turn the
ignition switch to ON
(
w
*1
, and goes
off when the engine starts.
•
Comes on when the engine oil
pressure is low.
•
Comes on while driving
- Immediately
stop in a safe place.
2
If the Low Oil Pressure Indicator
Comes On
Malfunction
Indicator Lamp
•
Comes on when you turn the
ignition switch to ON
(
w
*1
, and goes
off either when the engine starts, or
after several seconds if the engine
did not start.
•
Comes on if there is a problem with
the emissions control systems.
•
Blinks when a misfire in the engine’s
cylinders is detected.
•
Comes on while driving
- Have your
vehicle checked by a dealer.
•
Blinks while driving
- Stop in a safe
place where there are no flammable
objects. Stop the engine for 10 minutes
or more, and wait for it to cool down.
Then, take your vehicle to a dealer.
2
If the Malfunction Indicator Lamp
Comes On or Blinks
Charging
System Indicator
•
Comes on when you turn the
ignition switch to ON
(
w
*1
, and goes
off when the engine starts.
•
Comes on when the battery is not
charging.
•
Comes on while driving
- Turn off the
climate control system and rear demister
in order to reduce electricity
consumption.
2
102
uu
Indicators
u
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Shift Position
Indicator
*
•
Indicates the current shift position.
2
P. 519
—
Transmission
System
Indicator
*
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Blinks if the transmission system has
a problem.
•
Blinks while driving
- Avoid sudden
starts and acceleration and have your
vehicle checked by a dealer immediately.
Shift Up
Indicator
•
Comes on when shifting up is
recommended.
2
2
—
Shift Down
Indicator
*
•
Comes on when shifting down is
recommended.
2
—
M
(7-speed
manual shift
mode) Indicator/
Shift Indicator
*
•
Comes on when 7-speed manual
shift mode is applied.
2
—
* Not available on all models
103
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Seat Belt
Reminder
Indicator
•
Comes on if you are not wearing a
seat belt when you turn the ignition
switch to ON
(
w
*1
.
•
If the front passenger is not wearing
a seat belt, the indicator comes on a
few seconds later.
•
Blinks while driving if either you or
the front passenger has not fastened
a seat belt. The beeper sounds and
the indicator blinks at regular
intervals.
•
The beeper stops and the indicator goes
off when you and the front passenger
fasten their seat belts.
•
Stays on after you or the front
passenger has fastened the seat belt
- A detection error may have occurred in
the sensor. Have your vehicle checked by
a dealer.
2
Low Fuel
Indicator
•
Comes on when the fuel reserve is
running low (approximately 8.0
litres/1.76 Imp gal left).
•
Blinks if there is a problem with the
fuel gauge.
•
Comes on
- Refuel your vehicle as soon
as possible.
•
Blinks
- Have your vehicle checked by a
dealer.
Anti-lock Brake
System (
ABS
)
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
If it comes on at any other time,
there is a problem with the ABS.
•
Stays on constantly
- Have your
vehicle checked by a dealer. With this
indicator on, your vehicle still has normal
braking ability but no anti-lock function.
2
P. 634
(Red)
104
uu
Indicators
u
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Supplemental
Restraint System
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Comes on if a problem with any of
the following is detected:
-
Supplemental restraint system
-
Side airbag system
-
Side curtain airbag system
-
Seat belt tensioner
•
Stays on constantly or does not
come on at all
- Have your vehicle
checked by a dealer.
Passenger Front
Airbag On/Off
Indicators
•
Both indicators come on for a few
seconds when you turn the ignition
switch to ON
(
w
*1
, then goes off
after a system check up.
When the passenger front airbag is
active: The on indicator comes back
on and remains on for about 60
seconds.
When the passenger front airbag is
inactive: The off indicator comes
back on and stays on. This is a
reminder that the passenger front
airbag is deactivated.
2
Passenger Front Airbag Off System
P. 61
—
105
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Vehicle Stability
Assist (VSA)
System Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Blinks when VSA, or trailer stability
assist is active.
•
Comes on if there is a problem with
the VSA system, brake assist, hill
start assist system, trailer stability
assist or brake lighting system.
•
Stays on constantly
- Have your
vehicle checked by a dealer.
2
Vehicle Stability Assist (VSA)
System
P. 543
2
P. 512
2
•
When
TSA
is displayed on the driver
information interface, the VSA does not
activate.
•
Comes on if the VSA system is
deactivated temporarily after the
battery has been disconnected, then
re-connected.
•
Drive a short distance at more than 20
km/h (12 mph). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
106
uu
Indicators
u
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Vehicle Stability
Assist (VSA)
OFF
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Comes on when you partially disable
VSA.
2
•
Comes on if the VSA system is
deactivated temporarily after the
battery has been disconnected, then
re-connected.
•
Drive a short distance at more than 20
km/h (12 mph). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
Electric Power
Steering (EPS)
System Indicator
•
Comes on when you turn the
ignition switch to ON
(
w
*1
, and goes
off when the engine starts.
•
Comes on if there is a problem with
the EPS System.
•
Stays on constantly or does not
come on at all
- Have your vehicle
checked by a dealer.
2
If the Electric Power Steering (EPS)
System Indicator Comes On
P. 753
107
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
Low Tyre
Pressure/
Deflation
Warning System
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
May come on briefly if the ignition
switch is turned to ON
(
w
*1
and the
vehicle is not moved within 45
seconds, to indicate the initialisation
process is not yet complete.
•
Comes on and stays on when:
-
One or more tyres’ pressures are
determined to be significantly low.
-
The system has not been initialised.
•
Comes on while driving
- Stop in a
safe place, check tyre pressures, and
inflate the tyre(s) if necessary.
•
Stays on after the tyres are inflated
to the recommended pressures
- The
system needs to be initialised.
2
Deflation Warning System
Initialisation
•
Blinks for about one minute, and
then stays on if there is a problem
with the deflation warning system,
or when a compact spare tyre is
temporarily installed.
•
Blinks and remains on
- Have your
vehicle checked by a dealer. If the vehicle
is fitted with a compact spare, get your
regular tyre repaired or replaced and put
back on your vehicle as soon as you can.
•
Comes on if the deflation warning
system is deactivated temporarily
after the battery has been
disconnected, then re-connected.
•
Drive a short distance at more than 20
km/h (12 mph). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
108
uu
Indicators
u
In
strum
e
nt Pa
nel
*1:Models with the keyless access system have an
ENGINE START/STOP
button instead of an ignition switch.
Indicator
Name
On/Blinking
Explanation
Message
System Message
Indicator
•
Comes on for a few seconds when
you turn the ignition switch to ON
(
w
*1
, then goes off.
•
Comes on along with a beep when a
problem is detected. A system
message on the driver information
interface appears at the same time.
•
While the indicator is on, press the
(display/information) button to see the
message again.
•
Refer to the Indicators information in
this chapter when a system message
appears on the driver information
interface. Take the appropriate action
for the message.
•
The driver information interface does
not return to the normal screen unless
the warning is cancelled, or the
button is pressed.
—
Auto High-Beam
Indicator
•
Comes on when all the operating
conditions of the auto high-beam
are met.
2
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст