Honda Odyssey 2004. Manual — part 249
01
01
S0X4AA1E10411412282KAAT00
14-390
Automatic Transmission
Shift Lever Removal
D
B
A
G
E
C
F
D
B
A
C
SRS components are located in this area. Review the
SRS component locations, 2002 model (see page 23-19),
2003-2004 models (see page 23-20), and the
precautions and procedures (see page 23-21) in the SRS
before performing repairs or service.
1. Remove the steering column upper and lower
covers (see page 17-25).
2. Shift the transmission into the N position.
3. Remove the nut (A) securing the shift cable end (B),
then separate the shift cable (C) from the shift lever
assembly (D).
4. Rotate the socket holder (E) on the shift cable
counterclockwise a quarter turn, then slide the
holder to remove the shift cable from the shift cable
bracket (F).
NOTE: Do not remove the shift cable by twisting
the shift cable guide (G).
5. Disconnect the shift lock solenoid connector (A)
and the park pin switch connector (B).
6. Remove the three bolts (C) securing the shift lever
assembly, then remove the shift lever assembly (D).
03/07/29 09:40:40 61S0X050_140_0393
01
02
S0X4AA1E10411412282KCAT00
14-391
Shift Lever Installation
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
SRS components are located in this area. Review the
SRS component locations, 2002 model (see page 23-19),
2003-2004 models (see page 23-20), and the
precautions and procedures (see page 23-21) in the SRS
before performing repairs or service.
1. Install the shift lever assembly on the steering
column.
2. Turn the ignition switch ON (II), and verify that the
N position indicator comes on.
3. Install the shift cable end to the shift lever. If
necessary, adjust the shift cable (see step 5 on
page 14-395).
03/07/29 09:40:41 61S0X050_140_0394
01
S0X4AA1E10411412282MFAT00
14-392
Automatic Transmission
Shift Lever Disassembly/Reassembly
SHIFT LOCK
SOLENOID
SHIFT LEVER ASSEMBLY
8 x 1.25 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
WASHER
CONTROL BRACKET
CONTROL BRACKET
COLLAR
SELECT LINK
SELF-LOCKING NUT
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
SHIFT CABLE
SHIFT LEVER BUSHING
PIVOT WASHER
4 mm SCREW
3 N·m (0.3 kgf·m, 2 lbf·ft)
DETENT SPRING
SHIFT LOCK EXTENSION
SHIFT LOCK CUSHION
SHIFT LOCK SOLENOID PLUNGER
PLUNGER SPRING
4 mm SCREW
3 N·m (0.3 kgf·m, 2 lbf·ft)
WASHER
SHIFT LEVER KNOB
9 N·m (0.9 kgf·m, 7 lbf·ft)
Apply silicone grease to these parts:
• Sliding surfaces on the detent plate.
• Sliding area on shift lever and control bracket.
• Movable parts of the shift lock mechanism.
• Select link and shift lever contacting area.
• Select link and control bracket contacting area.
• One side of washer opposite of the self-locking nut.
• Pivot washer.
• Shift lever bushing.
03/07/29 09:40:42 61S0X050_140_0395
01
02
03
S0X4AA1E10411412281KBAT00
14-393
Shift Cable Replacement
D
B
A
E
C
F
B
A
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
C
D
E
SRS components are located in this area. Review the
SRS component locations, 2002 model (see page 23-19),
2003-2004 models (see page 23-20), and the
precautions and procedures (see page 23-21) in the SRS
before performing repairs or service.
1. Raise the front of the vehicle, and make sure it is
securely supported.
2. Set the parking brake, and block the rear wheels
securely.
3. Remove the steering column covers
(see page 17-25).
4. Shift the transmission into the N position.
5. Remove the nut (A) securing the shift cable end (B),
then separate the shift cable (C) from the shift lever
assembly (D).
6. Rotate the socket holder (E) on the shift cable
counterclockwise a quarter turn, then slide the
holder to remove the shift cable from the shift cable
bracket (F).
7. Remove the shift cable guide bracket (A) and
grommet (B).
8. Remove the bolts securing the shift cable holder (A),
then remove the shift cable cover (B).
9. Remove the lock bolt (C) securing the control lever
(D), then remove the shift cable (E) with the control
lever.
(cont’d)
03/07/29 09:40:42 61S0X050_140_0396
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст