Honda Odyssey 2004. Manual — part 489
01
02
11
S0X4A00J46660521021FEAT30
Tailgate (With Security System)
22-284
22-284
Power Door Locks/Factory Keyless/Factory Security
Door/Tailgate Key Cylinder Switch
Test (cont’d)
Door Lock Switch Test
B
A
A
B
Terminal
Position
OFF
1
2
UNLOCK
3
LOCK
1. Remove the tailgate trim panel (see page 20-61).
2. Disconnect the 3P connector (A) from the switch (B).
3. Check for continuity between the terminal in each
switch position according to the table.
4. If the continuity is not as specified, replace the
switch.
1. Remove the inner door handle (see page 20-7).
2. Remove the two screws (A), then remove the door
lock switch (B).
3. Check for continuity between the No. 1 and No. 2
terminals in each switch position.
• There should be no continuity with the door lock
switch in neutral or LOCK.
• There should be continuity with the door lock
switch in UNLOCK.
4. Check for continuity between the No. 2 and No. 3
terminals in each switch position.
• There should be continuity with the door lock
switch in UNLOCK.
• There should be no continuity with the door lock
switch in neutral or LOCK.
5. If the continuity is not as specified, replace the
switch.
03/07/29 10:25:59 61S0X050_220_0286
01
02
S0X4A00J46660558345FEAT01
05
S0X4A00J46660558361FEAT40
22-285
22-285
Tailgate Lock Actuator Test
A
A
Terminal
Position
LOCK
1
2
UNLOCK
1. Remove the tailgate trim panel (see page 20-61).
2. Disconnect the 2P connector (A) from the actuator.
3. Check actuator operation by connecting power and
ground according to the table. To prevent damage
to the actuator, apply battery voltage only
momentarily.
4. If the actuator does not operate as specified,
replace it.
1. Remove the tailgate trim panel (see page 20-61).
2. Disconnect the 3P connector (A) from the actuator
(B).
3. Check for continuity between the 2 and 3 terminals
in each switch position.
• There should be continuity with the knob switch
in UNLOCK.
• There should be no continuity with the knob
switch in LOCK.
4. If the continuity is not as specified, replace the
switch.
03/07/29 10:26:00 61S0X050_220_0287
Tailgate Lock Knob Switch Test
01
S0X4A00J46643432301FEAT30
22-286
Power Door Locks/Factory Keyless/Factory Security
Hood Switch Test
1. Open the hood.
2. Disconnect the 2P connector from the hood switch.
3. Check for continuity between the terminals.
• There should be continuity between the No. 1
and No. 2 terminals when the hood is opened
(lever released).
• There should be no continuity between the No. 1
and No. 2 terminals when the hood is closed
(lever pushed down).
4. If the continuity is not as specified, replace the
switch.
03/07/29 10:26:00 61S0X050_220_0288
*01
S0X4A00J16160700000DAAT00
22-287
Power Sliding Doors
Component Location Index
SLIDE MOTOR
RIGHT SLIDING DOOR
HANDLE SWITCH
RIGHT POWER SLIDING DOOR CONTROL UNIT
SLIDE MOTOR
RIGHT SLIDE MOTOR
REVOLUTION SENSOR
RIGHT SLIDING DOOR SWITCH
LEFT SLIDE MOTOR REVOLUTION SENSOR
SLIDING DOOR BUZZER
LEFT SLIDING DOOR SWITCH
LEFT SLIDING DOOR HANDLE SWITCH
RIGHT JUNCTION
SWITCH
KEYLESS DOOR LOCK
CONTROL UNIT
LEFT JUNCTION SWITCH
SLIDING DOOR SWITCH
No. 61 (30A) FUSE
MULTI-FUSE/RELAY BOX A
(’99-02 models)
REMOTE CONTROL SWITCH
REMOTE CONTROL SWITCH
No. 81 (30A) FUSE
UNDER-HOOD
SUB FUSE BOX
(’03-04 models)
LEFT POWER SLIDING
DOOR CONTROL UNIT
• LATCH POSITION SWITCH
• RELEASE MOTOR
• CLOSER MOTOR
• LATCH POSITION SWITCH
• RELEASE MOTOR
• CLOSER MOTOR
Test, page 22-309
Test, page 22-317
Input Test, page 22-304
Removal/Installation,
page 22-320
Test, page 22-309
Test, page 22-319
Test, page 22-318
Test, page 22-309
Test, page 22-317
Test, page 22-313
Input Test,
page 22-267
Test, page 22-313
Test, page 22-312
Test, page 22-311
Test, page 22-311
Input Test, page 22-300
Removal/Installation,
page 22-320
Test, page 22-310
Test, page 22-310
03/07/29 10:26:04 61S0X050_220_0289
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст