Honda Odyssey 2004. Manual — part 38
05
01
07
08
5-14
Engine Assembly
Engine Installation (cont’d)
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
10 x 1.25 mm
42 N·m (4.3 kgf·m,
31 lbf·ft)
12 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
12 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
10 x 1.25 mm
44 N·m (4.5 kgf·m,
33 lbf·ft)
5. Install the transmission lower front mount and
transmission lower rear mount on the front
subframe.
6. Install the rear mount on the front subframe.
7. Lower the hoist.
8. Tighten the front mount bracket support nut.
9. Install the side engine mount bracket, then tighten
the mounting bolts in the numbered sequence
shown.
10. Remove the chain hoist from the engine.
03/07/29 09:09:20 61S0X050_050_0014
09
10
11
12
5-15
10 x 1.25 mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
A
6 x 1.0 mm
12 N·m (1.2 kgf·m,
8.7 lbf·ft)
B
10 x 1.25 mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
10 x 1.25 mm
58 N·m (5.9 kgf·m, 43 lbf·ft)
A
6 x 1.0 mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
B
11. Raise the vehicle on the hoist to full height.
12. Remove the rope from the steering gearbox, and
install it on the subframe.
13. Tighten the power steering (P/S) hose clamp
mounting bolts (A), and install the harness clamp
(B).
14. Install the stiffeners.
15. Tighten the P/S hose clamp mounting bolt (A), and
install the P/S hose in the clamps (B).
(cont’d)
03/07/29 09:09:21 61S0X050_050_0015
*02
14
5-16
Engine Assembly
Engine Installation (cont’d)
C
10 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
A
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
C
10 x 1.25 mm
33 N·m (3.4 kgf·m,
25 lbf·ft)
B
B
D
B
C
10 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
A
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m,
8.7 lbf·ft)
D
C
E
B
6 x 1.0 mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
16. Install a new set ring on the end of each driveshaft,
then install the driveshafts. Make sure each ring
‘‘clicks’’ into place in the differential and
intermediate shaft.
17. Connect the suspension lower arm ball joints (see
page 18-17).
18. Connect the stabilizer links (see page 18-20).
19. Install exhaust pipe A (A); use new gaskets (B) and
new self locking nuts (C).
20. Connect the primary heated oxygen sensor
(primary HO2S) connector (D).
21. Install the control lever (A) with the shift cable on
the control shaft. Do not bend the shift cable any
more than is necessary to install the control lever.
22. Install the lock bolt (B) with a new lock washer (C),
then bend the lock tab of the lock washer.
23. Install the shift cable cover (D), then install the shift
cable holder (E) on the shift cable cover.
Replace.
Replace.
Replace.
03/07/29 09:09:22 61S0X050_050_0016
*04
16
06
*03
5-17
A
B
C
24. Install the splash shield.
25. Install the front tires/wheels.
26. Lower the vehicle on the hoist.
27. Install the upper radiator hose (A) and lower
radiator hose (B).
28. Install the water bypass hoses (C) (1999-2001
models).
29. Install the heater hoses.
30. Install the automatic transmission fluid (ATF) cooler
hoses for 1999-2001 models (see page 14-156) or
2002-2004 models (see page 14-389).
(cont’d)
03/07/29 09:09:23 61S0X050_050_0017
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст